Contribute
Register

No audio while using Headphone jack ALC3246 (256) (AppleALC)

Status
Not open for further replies.
have done, but no audio
 

Attachments

  • debug_30825.zip
    5.4 MB · Views: 62
Last edited:
maximmurmansk said:
Please help me to enable sound.
Last appleAlc lilu codeckcommander in L/E
Click to expand...
maximmurmansk said:
have done, but no audio
Click to expand...

Is it your intention to inject layout-id=13? Because that's what is shown in ioreg. You should check AppleALC documentation for valid layout-id values for your audio codec.

Note other values:
Code: 
u430:trackpad.git Admin$ ls -l ~/Projects/lilu/applealc.git/Resources/ALC256/layout*
-rw-r--r--  1 Admin  staff  32712 Sep  6 08:52 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout11.xml
-rw-r--r--  1 Admin  staff   1818 Oct 17 16:59 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout11.xml.zlib
-rw-r--r--  1 Admin  staff  32712 Apr 24  2018 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout13.xml
-rw-r--r--  1 Admin  staff   1818 Oct 17 16:59 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout13.xml.zlib
-rw-r--r--  1 Admin  staff  29234 Apr 24  2018 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout28.xml
-rw-r--r--  1 Admin  staff   3593 Oct 17 16:59 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout28.xml.zlib
-rw-r--r--  1 Admin  staff  32712 Apr 24  2018 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout56.xml
-rw-r--r--  1 Admin  staff   1818 Oct 17 16:59 /Users/Admin/Projects/lilu/applealc.git/Resources/ALC256/layout56.xml.zlib
 
I`ve tried all of them 11,13,28,56
Even VoodooHDA not enables audio
 
Last edited:
Maybe you know is it possible to extract audio pin config from win10?
Only in win10 sound works nice with mic.
 
Flemidra said:
Thank you so much, after installing ALCPlugFix and using terminal command "hda-verb 0x19 0x707 0x20" headhphone jack is working fine (as an output). I still dont have the microphone of my headphone enable but i will look into that. My priority now is to find out how to add that command line to codeccommander in order to load it automatically.


About this, before i tried to install all my kext using a kext utility like kext wizard. The kexts actually works but i get a lot of corrupted kextcache output, so i had to fresh install and then i start using the kext>others folder inside my clover. They are working "fine" (the only problem that im facing right now is the audio). But i will try to install again the kext to the system volume, i hope i dont have kextcache issues like before.
Click to expand...

Can you please tell me how to do it step by step because i didn't understand how you did it, my codec is also ALC3246, i am getting very low sound fro speakers and no sound from headphones. Thanks in advance
 
I have a similar problem

i had no bugs in my headphone and microphone, and if i connect a headphone in my headphone jack, it actually gets detected, the problem is, no matter what i do, i cant Hear anything using the built-in speaker, i can turn the volume up or down but there is no sound out of it.

I`ve tried all of them 5,11,13,28,56
Even VoodooHDA ，
and run
"hda-verb 0x1b SET_UNSOLICITED_ENABLE 0x83"
"hda-verb 0x1b SET_UNSOLICITED_ENABLE 0x82"
 
Try last appleALC kext 1.3.5 with layout-id 21.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top