Contribute
Register

Big Bertha's Big Brother:Asus Z10PE-D8 WS Dual Xeon Broadwell v4 CPU's 64GB DDR4 ECC RDIMM RAM

Status
Not open for further replies.
I found this guy on Geekbench with results that has over 68K.

Then I found him posting on this thread via google search with Z10PE-D16 WS and X10DAI config files. But I am not a member to login and download. Does anyone have access and or an invite code to joint he forum?

Link here, use google translate:
http://bbs.pcbeta.com/viewthread-1712877-1-1.html
 
Ok we're up n running - lots of tweaking to do, but it's installed and working... For now - lol
 
Struggling with this install, the change in CPU's was not as smooth as I had hoped and the previous installation didn'tlikethe change at all. Still fighting with graphics cards - The 660ti keeps booting to a black screen even with web drivers and clover NvidiaWeb set ... It usually gets correctly identified but this time it has not and neither has the screens, tried them as legacy and EFI. The web drivers claim they can't load and I can't uninstall them without the panel so need todo some reading to see if they can be removed via terminal.

Preliminary GB3 results ...
 

Attachments

  • Screen Shot 2016-10-20 at 21.25.52.png
    Screen Shot 2016-10-20 at 21.25.52.png
    95.6 KB · Views: 201
  • Screen Shot 2016-10-20 at 21.30.24.png
    Screen Shot 2016-10-20 at 21.30.24.png
    94.1 KB · Views: 220
Stability restored... Just like Z9PE-D8 it's snotty about what goes where, get it wrong and it all goes to crap!

GTX660Ti now back to working properly using PCIe slot 3. If you use Slot 1 with twin powered cards like the 660Ti, then you will CPU Socket Errors 90% of the time. In slot 2 you will get the success post beeb but you will not get any picture !

Still no functional Web Drivers but working well without them now that I am away from Legacy mode.

FakeLPC via Clover refuses to take or doesn't get applied so I need to do a DSDT fix for that, hopefully then I will achieve Power Management, all the required kexts are there other than AppleLPC so I am guessing that's what is making it fail. Only getting the one speed of 2.0Ghz so at least I am not wasting electricity whilst trying to get it implemented.
 
Got the M.2 drive working again and low and behold the Web drivers are now working as they should.
Getting slightly better GB3 scores but not worth posting until I see the difference with a working Power Management.
 
Good morning martin.... received my board yesterday and finally assembled everything... did not change anything on the board, placed the two CPU´s in the sockets, put 1 16Gb DDR4 dimm per CPU in the slot according to the manual, installed a 770GTX from my old hackintosh in the first slot connected my win10 SSD to Sata1... connected al cables etc... now when i try to start it it starts tu run down all its codes and gets stuck at "87" then a red SMD led starts to light up at CPU socket 1... the monitor remains black... no idea what BIOS version is installed... anything of that sounds familiar with you? did you ever use this blogger function? any ideas or recommendations? attached some pictures of my build

*edit* CPU1 heat sink remains cool while CPU2 heat sing gets quite hot, maybe thats also an important observation
 

Attachments

  • 2016-10-20 18.57.40.jpg
    2016-10-20 18.57.40.jpg
    2.1 MB · Views: 190
  • 2016-10-20 18.36.14.jpg
    2016-10-20 18.36.14.jpg
    2.6 MB · Views: 196
  • 2016-10-20 17.32.54.jpg
    2016-10-20 17.32.54.jpg
    2.1 MB · Views: 187
  • 2016-10-20 17.06.49.jpg
    2016-10-20 17.06.49.jpg
    2.9 MB · Views: 202
Last edited:
Panamamax said:
Good morning martin.... received my board yesterday and finally assembled everything... did not change anything on the board, placed the two CPU´s in the sockets, put 1 16Gb DDR4 dimm per CPU in the slot according to the manual, installed a 770GTX from my old hackintosh in the first slot connected my win10 SSD to Sata1... connected al cables etc... now when i try to start it it starts tu run down all its codes and gets stuck at "87" then a red SMD led starts to light up at CPU socket 1... the monitor remains black... no idea what BIOS version is installed... anything of that sounds familiar with you? did you ever use this blogger function? any ideas or recommendations? attached some pictures of my build

*edit* CPU1 heat sink remains cool while CPU2 heat sing gets quite hot, maybe thats also an important observation
Click to expand...

Nice Photos dude !!
Move GPU to PCIe 3 - Only motherboard powered GPU's will work in PCIe 1 i.e. older Quadro cards
Red light woes have been the bane of my life over the last few days.

Most common halts here have been 87 91 94 95 96 97 b7

Never used the blogger as I don't have another computer to read the results - great idea if you have another PC/laptop

Martin

** Edit **
Where's my manners ? ... Good morning back atcha!! :)
 
heavent been home yet to try the change of the GPU... however does anybody know where to find the BIOS updates for this board? i cannot find anything on the asus support page to the motherboard...
 
i have the same score but its cause the system clock runs to fast with the unofficial CPU, so geek bench thinks you finished faster than its actually happened :) making render tests with 100% cpu i am exactly with the same speed with the clock fixed (40.000 points or without the clock fixed (65.000 points)
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top