Correct, I am working with a generic install just to try to solve these issues and learn. I have a solid install on another that I have added the serial number and have messages working. Of course booting with iGPU Disabled or in Auto.
Of course at my knowledge level I may not understand how...
@macnb
The post on a previous thread where you explained that you configured your own system gives an EFI for me to try, but I have not seen a list of the kexts you load. Your and my system are pretty much identical. Gigabyte GZ-Z77X-UP5-TH, i7-3770K, RX 580. I am booting from Samsung SSD...
Thanx macnb. Very interesting about APFS filling. I have included a screenshot of 'Get Info'. It is mainly empty. When I follow your steps to boot, it boots normally. The only time I have a problem is when MultiBeast has been run and the iGPU is enabled. I loaded the Mojave just fine with it on...
Thanx pastrychef. It's not that it won't. In fact during the last install I had it enabled and it showed both video cards after in the System Report. However, once I ran MultiBeast, it went back into the reboot loop. Meaning, about halfway through boot, it will reboot. Both from trying to boot...
I hope this in correct section, please advice if not.
CONDENSED VERSION BETWEEN THE LINES BELOW
First of all I would like to thank everyone who contributes to this site. Both with questions and with answers. I have been part since 2013. I believe Mountain Lion was the first OS I loaded on my...
Well Bummer. After MultiBeast install I went back into reboot loop with iGPU enabled in BIOS. I had to change it back to Auto to boot. I wonder if it is some sort of clover issue? Anyone with any thoughts? Booted fine and showed both Graphics Adapters in System Report before MultiBeast 11.0.1...
Thank You. Yes, I have done that previously. Here is where I am now. I tried setting iGPU to enable in BIOS and got a reboot loop. So I decided to chose another drive and start a fresh install to try a few things. I set iGPU back to Enabled, 512M, Max. Install went wonderfully and I show both...
THANK YOU for your input :wave:
I am going to try your suggestions. I have been running my iGPU set to Auto. I have wondered if there is a difference from Enabled. When I set it to Enabled, I get a reboot loop. It boots so far then reboots. The verbose text is so fast I cannot see what is...
I run a Asus RX580 and both screens light up during the Mojave install. I have both running right now with no configuration yet. I have yet to install even WhateverGreen. Not saying I won't. Just trying to figure out what advantage it gives. My RX 580 is reported properly in 'About' and is...
FIXED!!: I always like when a solution is posted, so I am letting everyone know it is solved and how. I must thank @RehabMan. He solved it indirectly. I began reading his FAQ on things to do before asking a question. I came to the part describing how to load kexts manually. I removed the...
FIXED!!: I always like when a solution is posted, so I am letting everyone know it is solved and how. I must thank @RehabMan. He solved it indirectly. I began reading his FAQ on things to do before asking a question. I came to the part describing how to load kexts manually. I removed the...
Thank You pastrychef. I am sorry for forgetting to include that. Yes, I did have them there as well. They did not load from there either. Then I had a response and read that as you say, they shouldn't be there so I used KextBeast and installed them in /L/E thinking surely that would work. I...
Thank You for your input!
I have been :banghead: for two nights now on what seems to me should be a simple thing to do. I downloaded WEG and NoVPAJpeg. I copied them to /L/E and rebooted. No result. So I started digging. Everything I found says this is the proper procedure. I finally came to...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.