Recent content by mancinaa2011

  1. mancinaa2011

    Motherboard recommendation for Yosemite!

    Hi guys, A thread revival! I stayed away from doing a hackintosh in the end but would like to give it another crack I think! Still have the same parts so an i5 2300, can someone recommend me a motherboard that I can use with the least amount of messing around with DSDT's and so on...
  2. mancinaa2011

    boot0 Error

    Anyone?
  3. mancinaa2011

    boot0 Error

    I have tried to fix this error following the TonyMac guide but when I do it I get an error; cd /Volumes/"USB" dd if=boot1h of=/dev/disk0s2 dd: boot1h: Device not configured (HERE IS MY ERROR) 0+0 records in 0+0 records out What is going wrong? Thanks
  4. mancinaa2011

    Motherboard recommendation for Yosemite!

    It is an i5 2300(1155), I would like to use my discrete gfx (GTX 460SE) and ok thanks mate will have a look for one!
  5. mancinaa2011

    Motherboard recommendation for Yosemite!

    Hi guys, Currently have an i5, Asus P8H61-M and 8gb of ram I would like to turn into a hackintosh. From what I can gather my motherboard wouldn't be compatible? I certainly haven't seen a DSDT for it! So fellow "hackintosher's" what motherboard should I buy that will enable me to make...
  6. mancinaa2011

    Suggestion for rear USB/Audio connections PowerMac G5 (late 2005) (no cutting)

    I have actually been considering using the same thing but modding it to fit in the front panel of the G5. See my thread; http://www.tonymacx86.com/powermac-g5/100636-mancinaa2011s-basic-g5-mod.html I have been trying to find the dimensions but not even Bitfenix will tell me! Could you...
  7. mancinaa2011

    Possible to wire up power button without front logic panel?

    That is true. However my friend has years of experience of soldering DC jacks in laptops and replacing capacitors on motherboards etc so I was going to get him to do it for me. He certainly has the best chance. I figure by sticking some cardboard in between each point that will limit the...
  8. mancinaa2011

    Possible to wire up power button without front logic panel?

    I am just thinking. Would it be possible to just strip the motherboard header cable and solder it directly to the PCB? rather than stripping the cables that are already attached? Would I have to desolder the original cables and then solder the new ones in place or can I just hold the cable on...
  9. mancinaa2011

    Possible to wire up power button without front logic panel?

    Thank you :) Yeh I may as well wire it up, that way I can plug it in if I decide to. So would I then do Positive LED - W Negative LED- B Negative Power-B Positive Power- R Would that be correct?
  10. mancinaa2011

    Possible to wire up power button without front logic panel?

    The left ones but looking at it which way :p If someone could just confirm which letters I use that would be simpler haha :) Thanks rehpotsirhc though :)
  11. mancinaa2011

    My G5 Case

    Looks a good idea. What motherboard tray is that? looks very nice.
  12. mancinaa2011

    A Simple G5 Case Mod

    Thanks guys, sounds like a good plan. Will try that tomorrow :)
  13. mancinaa2011

    A Simple G5 Case Mod

    Hi, I have been following your thread the "A Simple G5 Case Mod" and I was just wondering if you could help me. I am up to the stage where I now need to put in my motherboard and cut my slot for the IO. Now, I see you mention that you should use the shorter stand offs so I was just wondering...
  14. mancinaa2011

    A Simple G5 Case Mod

    Ah I understand now. Thank you buddy :)
  15. mancinaa2011

    A Simple G5 Case Mod

    I have just got a G5 case and I am not too confident in chopping it all up straight away so I am thinking of following your guide to get me started :) I have a few questions, the stand offs that you have used. Did you buy them? if so where from! :D Secondly, once the stand offs are in...
Top