Recent content by jc123

Could you explain further on how to boot into single user mode or link me some single user boot mode info?

There’s got to be a way to get the verbose logs from the drive without booting into Mac OS right?

Yea I found that guys P52 configs a while back before I posted and tried all of them with small edits to the memory portions. I think the reason the config works for @professoramx is because he’s got an i7 and not the Xeon coffee lake refresh. The previously mentioned p52 config (E-2176m...

Hey Jay, so I tried 0x3E9B0009 and unforunately I'm unable to reach the installer with this platform ID, The only one I can seem to reach the installer with is 0x591B0000. Do I need to specify devices->properties->PciRoot(0)/Pci(0x02,0)-> deviceid to match this? as of now its commented out...

Hey bro thanks for your response, I've actually seen that post and tried all of the configs myself and all of them result in the same issue during second phase install. Glad you got yours working though. BTW what are your BIOS settings just incase?

When you say the CPU might not be supported do you mean unsupported by clover/weg/lilu or by macOS itself? I also tried a catalina USB and had the same result. also just fyi when I say the installer crashes at 15/12 mins I mean it crashes consistantly 30s-1 min into the second phase of the...

Thanks for your reply jay, and sorry I didn't realize it was against the rules to PM mods. Unforunately the edits you suggested left me with the same result. It doesn't seem to be a graphical glitch though. The installer crashes and reboots on the second phase over and over at 15 mins remaining...

I wanna say the only real issue is getting the proper platform id and framebuffer for my CPU, but its so new I can't find any documentation on it. Again, if you know anyone who can help me with editing those parts of my config that would be sweet. Thanks again for all your help. You've helped me...

These top 2 plists are for kabylake processors, mine is coffeelake, I'll try them anyway though, thanks! Also I can't even get past the installer to use hackintool for framebuffer patching so I'm kinda stuck =\. Would it be possible to use hackintool on my other hackintosh to edit the config on...

This is quite a lot to take in, I've followed the guide as well as I can, removing boot flags, and deleting entries in my config.plist. Most of the other stuff seems done already. I'm not quite sure what to put in the highlighted area in the attached screenshot. My CPUs device ID is 0x3E94...

It's crashed about 15 times now either on language selection screen or during install with 0x12345678 as the ig-platform-id, but I can't get to the installer without it. Do you know of any other solution to getting past IOConsoleUsers: GIOScreenLockState, hs 0, bs 0, now 0, sm 0x0 without an...

I've tried different variations of fakeID uncommented with default value and 0x12345678, ig-platform-id uncommented with default value and 0x12345678, and it either crashes/reboots after some time in language selection or installation or it reboots after IOConsoleUsers: GIOScreenLockState, hs 0...

Ok, so it crashed during the installer after the second reboot, now if I choose install Mac OS from Mojave (my drive name) it says mojave can't be installed on your system because the installer resources could not be found. I retried the entire process and it sometimes crashes and reboots on the...

reverting the previous and uncommenting ig-platform-id only and changing it to 0x12345678 has brought me to the installer now without crashing after a few seconds. installing now; will update.

I tried uncommenting intelgfx under fakeID and changed the value to 0x12345678 as well as changing my ig-platform-id to the same and it now gets to the installer, but it blacks out and reboots after 5-6 seconds. My graphics is UHD P630, not UHD 630, not sure if this could cause an issue. processor