Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

[Ayvan]

It's very strange... Now I removed all USB SSDT's (testing some configurations for a last hour), insert USB 3.1 drive... And it appears on SS01!

 

[Ayvan]

Another reboot... Ooops, on SS02!

Then, connect Type-C -> DisplayPort converter (using it for MacBook), disconnect, connect USB 3.1 drive... Now on SS01!

Disconnect and connect it severla times... SS01... Wait for a miniute after disconnect, connect again... SS02!

Ooops, I know! It's because port is 2-sides port!

When I connect it one side - SS01, rotate it 180 degrees... SS02!

Back panel port always SS06 for USB 3.1 drive.

 

[CaseySJ]

Another reboot... Ooops, on SS02!

Then, connect Type-C -> DisplayPort converter (using it for MacBook), disconnect, connect USB 3.1 drive... Now on SS01!

Disconnect and connect it severla times... SS01... Wait for a miniute after disconnect, connect again... SS02!

Ooops, I know! It's because port is 2-sides port!

When I connect it one side - SS01, rotate it 180 degrees... SS02!

Back panel port always SS06 for USB 3.1 drive.

Yes you're right! One orientation = SS01, flip it and it goes to SS02... For this we need to set Type to 10 (0x0A) instead of 0x09. Let me see if that makes any difference...

EDIT: We still have to enable both SS01 and SS02. Type 10 (0x0A) is, I believe, the technically correct value so I'll set them both to that.

 

[Ayvan]

Looks like sleep and wake works good with all this USB devices... I have 21 (including SS01).

 

[CaseySJ]

Looks like sleep and wake works good with all this USB devices... I have 21 (including SS01).

Yes it appears to work fine on Vision D as well. Will wait a day or two before updating the build guide.

Will add your Vision G information as well.

 

[Ayvan]

Yet, I prepared SSDT's removing SS08, HS08, HS14 (I did not found connectors for this devices) and set connector types for all ports.

 

[CaseySJ]

Yet, I prepared SSDT's removing SS08, HS08, HS14 (I did not found connectors for this devices) and set connector types for all ports.
View attachment 475112

Awesome. I've also removed non-existent ports. Will add a section to the build guide for Vision G.

 

[Ayvan]

When testing sleep I'm facing another problem...
My PSU Thermaltake Toughpower Grand RGB 1050W Platinum has USB module (monitoring, RGB control etc.), and It wakes up my PC after 1 sec of sleep...
I disconnect it during the test, but may be exist way to fix this? It connected to internal hub for 4 ports named HS02, but another user of this hub is my NZXT USB HUB (it's internal hub for my cooler, NZXT case internal controller and NZXT HUE 2 RGB controller) and it works good and not wake my PC up, and I can control my NZXT devices using liquidctl.

 

[CaseySJ]

When testing sleep I'm facing another problem...
My PSU Thermaltake Toughpower Grand RGB 1050W Platinum has USB module (monitoring, RGB control etc.), and It wakes up my PC after 1 sec of sleep...
I disconnect it during the test, but may be exist way to fix this? It connected to internal hub for 4 ports named HS02, but another user of this hub is my NZXT USB HUB (it's internal hub for my cooler, NZXT case internal controller and NZXT HUE 2 RGB controller) and it works good and not wake my PC up, and I can control my NZXT devices using liquidctl.

When the system wakes up after 1 second, does the display monitor also wake up? If the monitor stays black, what happens if you don't touch the system for 60-90 seconds? Does it go back to sleep?

 

[Ayvan]

When the system wakes up after 1 second, does the display monitor also wake up? If the monitor stays black, what happens if you don't touch the system for 60-90 seconds? Does it go back to sleep?

Yes, all system wakes up, including monitor, as when I press key on keyboard. I think, USB module on PSU sends signals, but I don't know why) When I disable HS02 via SSDT system sleeps normally.