- Joined
- Feb 3, 2011
- Messages
- 1,348
- Motherboard
- Gigabyte Z390 AORUS Ultra
- CPU
- i9-9900K
- Graphics
- RX 590
guide asrock z77 pro3 bios 1.90
1. patch your bois with pmpatch or http://biosrepo.wordpress.com/2. bois config oc tweaker change cpu ratio to per core other wise sleep wont work,disable internal pll over voltage.
3.advaced north bridge config, primary graphics adapter pci express,shared memory to 32mb if set to 64mb wont boot.
4.storage config ahci and set osx hdd to hot plug disabled other wise it will be shown as external
5.super io config disable serial port.
6.dont change anything else in bois its not needed save and exit.
7.for power management and system defs MacMini6,1 for i5 and i7 6,2 these r for ivy mobo/cpus dont use 13,1 or 13,2 only has 2 p states. asrock z77 pro3 is in the repo pjalm/toleda patches work great with no issues
8.this build is working 100% including sleep havent tested airplay i have no need for it
note if using more than 4gb ram for install use flag maxmem= amount of ram u have minus 2gb example 16 gb=14336
Trouble shooting guide. boot with -v verbose this works with all osx versions
Please remove any hardware thats not needed for install such as extra hdds,pci/pcie cards all of them if u have an incompatible hardware you will get iobluetooth hang can be caused by gfx/fakesmc kext if not loaded.lans such as bcm or killer nics should be disabled in bios for a fresh install.Disable vt-d in bios if your cpu has vt-d use flag dart=0 If u get a kp=kernel panic it because your hardware is incompatible or a bad kext in the efi/efi/kexts/other folder.Boot flags reboot system when you see the bootloader u have 5 secs to act press the spacebar.Now put in each pcie/pci device one at a time and reboot with -v each time to make sure theres no issues.If u get pci config begin then add flag npci=0x2000 or npci=0x3000 for nvida cards. System defs if you choose wrong smbios use SMBIOS=Null flag.Thanks for reading this boring guide. If you have any complaints keep it to yourself.
system freezes
a bad stick of ram or a bad dim port or you have xmp enabled in bios or your using dual channel and need to increase ram voltage,ssd needs firmware update,ssd has trim enabled check your ssd manufacture for details some ssd will freeze if trim enabled,or fakesmc plugins is causing this or a failing psu. bad kexts such as lan will too.
1. patch your bois with pmpatch or http://biosrepo.wordpress.com/2. bois config oc tweaker change cpu ratio to per core other wise sleep wont work,disable internal pll over voltage.
3.advaced north bridge config, primary graphics adapter pci express,shared memory to 32mb if set to 64mb wont boot.
4.storage config ahci and set osx hdd to hot plug disabled other wise it will be shown as external
5.super io config disable serial port.
6.dont change anything else in bois its not needed save and exit.
7.for power management and system defs MacMini6,1 for i5 and i7 6,2 these r for ivy mobo/cpus dont use 13,1 or 13,2 only has 2 p states. asrock z77 pro3 is in the repo pjalm/toleda patches work great with no issues
8.this build is working 100% including sleep havent tested airplay i have no need for it
note if using more than 4gb ram for install use flag maxmem= amount of ram u have minus 2gb example 16 gb=14336
Trouble shooting guide. boot with -v verbose this works with all osx versions
Please remove any hardware thats not needed for install such as extra hdds,pci/pcie cards all of them if u have an incompatible hardware you will get iobluetooth hang can be caused by gfx/fakesmc kext if not loaded.lans such as bcm or killer nics should be disabled in bios for a fresh install.Disable vt-d in bios if your cpu has vt-d use flag dart=0 If u get a kp=kernel panic it because your hardware is incompatible or a bad kext in the efi/efi/kexts/other folder.Boot flags reboot system when you see the bootloader u have 5 secs to act press the spacebar.Now put in each pcie/pci device one at a time and reboot with -v each time to make sure theres no issues.If u get pci config begin then add flag npci=0x2000 or npci=0x3000 for nvida cards. System defs if you choose wrong smbios use SMBIOS=Null flag.Thanks for reading this boring guide. If you have any complaints keep it to yourself.
system freezes
a bad stick of ram or a bad dim port or you have xmp enabled in bios or your using dual channel and need to increase ram voltage,ssd needs firmware update,ssd has trim enabled check your ssd manufacture for details some ssd will freeze if trim enabled,or fakesmc plugins is causing this or a failing psu. bad kexts such as lan will too.
Attachments
Last edited: