GA-Z97M-D3H + i7 4790k - Where am I going wrong ?

I do not know where I am going wrong , I've tried every way, with clover and unibeast and am getting the error images below.

My hardware:
2x8GB Corsair
i7 4790k
ga-z97m-d3h
cx430 corsair
no grpahics i use integrated graphics intel 4600

First shut down your system completely. Remove all but one stick of ram. Restart your system
and boot from the Unibeast USB. You should also disconnect sata cables to your Windows drives
when trying to install OS X.

trs96 said:

First shut down your system completely. Remove all but one stick of ram. Restart your system
and boot from the Unibeast USB. You should also disconnect sata cables to your Windows drives
when trying to install OS X.

Click to expand...

I did exactly what you asked, but still the error appears below.

Try one of the other sticks of ram in place of that one. You can also try the various ram
slots. May be that one of them is not working properly. Happens more than you'd think
even with new motherboards.

I just finished my hackintosh with the GA-Z97MX-Gaming 5 and i7 4790k

I had the RAM in the wrong slot.
Use one stick of RAM in the slot closest to the CPU.
Remove the GPU completely from the board. and just plug into the HDMI of the onboard graphics.

Boot hold F12. then at the Chimera screen (if you can get there) start typing

nv_disable=1

then enter.

Make sure to remove your windows drive too.

I don't know what GPU (if any) you are planning to use but I had no success with the GTX 960.

Hope this gets you started.

Tandy said:

I just finished my hackintosh with the GA-Z97MX-Gaming 5 and i7 4790k

I had the RAM in the wrong slot.
Use one stick of RAM in the slot closest to the CPU.
Remove the GPU completely from the board. and just plug into the HDMI of the onboard graphics.

Boot hold F12. then at the Chimera screen (if you can get there) start typing

nv_disable=1

then enter.

Make sure to remove your windows drive too.

I don't know what GPU (if any) you are planning to use but I had no success with the GTX 960.

Hope this gets you started.

Click to expand...

My hardware:
2x8GB Corsair
i7 4790k
ga-z97m-d3h
cx430 corsair
no grpahics i use integrated graphics intel 4600

*****************************************

i tested clover yosemite 10.10 and came error black screen it logo stop

bootflags:
-v kex-dev-mode=1 -gux_defer_usb2 -gux_no_idle

gruponarede said:

My hardware:
2x8GB Corsair
i7 4790k
ga-z97m-d3h
cx430 corsair
no grpahics i use integrated graphics intel 4600

*****************************************

i tested clover yosemite 10.10 and came error black screen it logo stop

bootflags:
-v kex-dev-mode=1 -gux_defer_usb2 -gux_no_idle

View attachment 133136

Click to expand...

Try with USB2.0 Ports, if you have multiple chipset controlled USB ports are there in MB, then try with different different ports. (Avoid front panel ports)

Check the below BIOS settings,

1. Enable USB Legacy Support
2. Set xHCI mode as AUTO (Not SMART Auto)
3. Set xHCI Hand-Off as Enabled
4. Enable the EHCI Hand-off
5. Disbale VT-D
6. Set SATA Mode as AHCI

Try to boot with "dart=0 USBBusFix=Yes -f -v -x" (From Unibest USB)

You sound like your doing what I did, I had no success for a while. So I thought to try Clover instead of Unibeast. Then finally back to Unibeast with Yosemite. I even went down to Mavericks with Unibeast, but nothing.

It was finally the misplaced RAM. Really just follow the instructions with Unibeast. I was having errors because of the RAM. Take out the extra RAM just use one stick closest slot to the CPU. and use the BIOS that Jithin.C.V suggests (most important disable VT-D)

once you get to the USB Chimera screen (with the cute apple on top) type maxmem=4096 you may not need the -x.

You may also want to try upgrading the BIOS to the latest version as well through Q-flash and the BIOS on another USB. I made sure that was the first thing I did with the Motherboard.

Just to give you hope. I posted my video at the video section http://www.tonymacx86.com/videos.php?show=single&vid=124

It really is great once you get through the hard stuff.

Good Luck!

I managed to perform the installation , made ​​a new clover usb, but now I get this problem on the screen right after the boot

my config.plist
View attachment config.plist

I wonder how can I check if my video is with acceleration QE / CI working

Update your build's hardware details under Profile > Basic Information section in the below format (Profile link is available on the upper right side of this website), So that we can avoid scroll back to your fist post for identifying the hardware details.

System : Motherboard + Bootloader(Clover/Chameleon/Chimera)
CPU : Detailed CPU Model
Graphics : All Graphics Devices

For Example,
System : GA-EP43T-USB3 (Chameleon)
CPU: Intel Quad Core Q8400
Graphics : ZOTAC GeForce 240GT

gruponarede said:

I managed to perform the installation , made ​​a new clover usb, but now I get this problem on the screen right after the boot
View attachment 133281
my config.plist
View attachment 133282

I wonder how can I check if my video is with acceleration QE / CI working

Click to expand...

Is the default config.plist which is putting by the installer.? Seems like wrong for you.

You have the fully enabled intel HD graphics..