Search results

Great! Thanks!! I guess I have to let my freq flag fly...

Dear wildwillow, You are a marvel, thank you so much!:clap: In the end fixed everything by re-running ssdtPRGen.sh and deleting the first attempted ssdt and copying a new one in, plus running completely optimized defaults in BIOS (except disabling VT-g) worked fine, with the memory turning to...

Interesting, with the usb as boot disk and memory speed set to default in the BIOS (1333MHz) it boots with ssdt.aml in place as made, and the cinebench now is very decent (48 fps and 730 cb). So something works! Now I will go back and check the tools in the power management thread. Should I...

Hi Wildwillow, I guess I did not read it enough time! I successfully ran the ssdtPRGen.sh and it found the Broadwell. I did not know what to do when it asked about the .dsl and copying it into /Extra, so I found it and copied the ssdt.aml that it created into EFI:/clover/acpi/patched. But upon...

Dear Bombardier and wildwillow, Thanks, I rebuilt without the sensors and with the SSDT-1.aml, into an HDMI at 1080p, boots reliably with full memory buffer. Now need to get it up to speed! Bombardier, would you possibly share your SSDT for the i7-5775C? It is for upping the power states? Or...

Bingo! Yes, from either port, HDMI or DVI to a real DVI monitor (not what I had before, a VGA with a cable terminating in a DVI plug) I get the full 1536 MB Ram on iMac 16,2, with just SSDT-1.aml. Thanks!! Now I have to optimize, will get back to you with results, tried running Multibeast...

I tried with copying both SSDT (although admittedly using an i5-5675 can't be right for an i7-5775C). with both it gets to a series of [IGPU] steps then goes into in6_unlink_ifa: IPv6 address 0x1cb08620e5452da3 has no prefix IOPPF: XCPM mode then it hangs. with just the SSDT-1.aml it ends in...

Dear Wildwillow, I cannot thank you enough for trying to help me. Simple question: when you write 'install' the SSDT, is it sufficient to use EFI Mounter v3 to mount the boot disk's EFI partition, then copy the .aml file into the right folder (EFI/EFI/Clover/ACPI/Patched)? Or is there another...

I have been trying to get a Broadwell i7-5775 with Iris Pro 6200 to run on a GA-Z97N-WIFI, now using the new Multibeast 8.1. I get no problems with the initial install and registration of OS X 10.11.3, and no problem with internet, but I never seem to be able to shift the IrisPro6200 from 3 MB...

Will there be a new uni and multi to go with the new 10.9.2 install mavericks from scratch?

Article: OS X 10.9.1 Update Word of warning, I installed the app store version automatically and fixed audio driver, no problems there. THe problem is that I can no longer boot from the other disks on my system (mountain lion, clone of original hd, copies of such, etc.) I will wait for the...

Yes, I am trying this with just one drive now. First I had Win7 on an Munchkin mSATA right on the MB, but then I saw attempts to understand the presesnce of NT drives in a -v boot so I took it out. It is a Samsung Pro 128 GB SSD attached to the SATA3 port P0. I originally used the optimized...

Dear Kongzilla, Thank you very much! I tried with the DSDT-free and the bootloader checked, but to no avail. Would you use the newer or older bootloader? Does it help to use any of the ACPI-rollbacks? I can't boot in OSX except once right after a fresh partition and new ML unibeast loading...

I am having a bear of a time getting ML10.8.3 to load at all on the Gigabyte GA-Z77X-UP4-TH. I have tried bios 7, 8, 9, 10a, all the same: Win 7 no problems at all. i7 3770k 16GB 1866 running as 1333. 1 SSD 1 partition. used all guides, bios settings as rec on these forums, Unibeast: no...