Recent content by teddydropdead

As i wrote, everything appeared to be laggy, but the cause was my old harddrive which has been replaced by an SSD now.

I know you guys already tried disabling the integrated graphics card, but i had a similar problem which i am trying to fix currently, so check up my thread if you want to: https://www.tonymacx86.com/threads/hs-nvidia-gtx-780-web-drivers-no-signal-after-boot.243292/#post-1672406 Good Luck :)

ADDITION: I could finally boot, by disabling InjectNvidia and the following Changes inside the BIOS: IGPU Dual (Lucid) disabled Shared Memory from fixed "64MB" to "Auto" to disable the onboard graphics card The system is now booted showing my "GTX 780 3GB" correctly Everything still seems...

Hello community, i just switched from Sierra to High Sierra and i can boot to the Desktop without my Nvidia GTX 780 just fine. I removed the old Web Drivers, rebooted, did the SIP magic, followed the guide here...

So, after quite some hours now what i did and the result. At first i tried to downgrade the BIOS on my HP and found out, that once you flash a newer Version F.36 for example, you can only downgrade to F.35 and not F.16. (wanted to check if i can write the EFIvars there) I then took your list...

Ahhh, i must have reactivated it when booting back to my current Windows 10 Setup, but i will check that later when being home again, Thank you very very much!

Thank you for your reply. I was able to set the SwitchableGraphicsVariable, is it possible that only some variables are locked? Because if not, i will have to use the way described above by manually copying the hex data by using setvar in the clover shell which hopefully is able to update the...

Thank you very much for answering, but i am far beyond this point. I have written i extracted the BIOS and found the offset, which you can see in the files attached to this answer. Grayout If: {19 82} 0x7420C Variable 0x297 equals 0x2 {12 86 97 02 02 00} 0x74212...

Hello hackintoshers, back from the dead I now own a new notebook since some months and now finally had the time to test out the mackintosh installation. My specs: HP Envy 15-ae020ng Mac OS 10.12 - Sierra Intel HD 5500 Graphics system currently running on an external drive Now to my problem...

Hey Guys! I finally made it work! I booted with the onboard Graphics from my Backup Partition (Backups are great!) Used it to install Clover to a USB Stick and then booted my primary partition from the Stick and voila! Graphics working smoothly via DVI, Nvidia Control Panel showing up in...

Good morning from Germany, i changed the system Definition to Mac Pro 3,1 via Multibeast, added kext-dev-mode because of a kext for phone USB tethering and checked the GraphicsEnabler=Yes option, but the Problem is still there. As soon as the login screen should appear, the monitor looses its...

Thank you for the Tip, i will try changing the System Definition to Mac Pro 3,1 tomorrow and report back if the Problem is gone then.

Thanks for Answering, I am using the following Definition: MacBook Pro (13 Inch, Mid 2010) because of the serial Number injected to make the App Store working. Could the System Definition cause the Graphics Card to not being supported?

Thanks Mate for the Reply, I am using the Chimera Bootloader v4.1.0 from the latest Multibeast 7.3.0 for Yosemite. Build Date 2015-04-22 # 20:46:10 I tried GraphicsEnabler=Yes already, but there was only the signal lost. I would install and use Clover, but i am more familiar with...

Hello Guys, I recently bought an Nvidia based ASUS GTX 560 DirectCU 2 OC to upgrade my system. Now i connected my Screen via the DVI connector on the Card to my Monitor and set the BIOS to my PCI Express Graphics card. Now booting with -v works fine, but as soon as the boot process is over...