Recent content by lassee

  1. lassee

    Will my build work - I am a beginner to Hackintosh

    No. I am not familiar with all the terms. But I will give it a go. Should I take the GPU out and use the onboard graphics?
  2. lassee

    Will my build work - I am a beginner to Hackintosh

    I am trying with the 770 installed :think:
  3. lassee

    Will my build work - I am a beginner to Hackintosh

    I tried -x now with same result. Computer freezes
  4. lassee

    Profile Build Signatures: Request Additional Components

    Second this Also MB ASROCK Z87M Extreme4 - Socket 1150
  5. lassee

    Will my build work - I am a beginner to Hackintosh

    Ok. Thanks. Will do. I did add my system under the profile, but it does not show. I therefor added my info in my signature. My MB nor the CPU I chose is in the listings
  6. lassee

    Will my build work - I am a beginner to Hackintosh

    I tried: PCIRootUID=0 PCIRootUID=1 Both gives me the grey screen with Apple logo that freezes up -v PCIRootUID=0 -v PCIRootUID=1 Both runs and ends up freezing like the former screenshot I have been looking in the forums to look for any solutions but I fear my technical knowledge is not...
  7. lassee

    Will my build work - I am a beginner to Hackintosh

    PCIRootUID=0 How/where do I add code? So now, boot with: -v PCIRootUID=0 When trying this, I end up at the same screen. Probably since I don't know where to add the code? I just ran the command. Thanks for all the help btw.
  8. lassee

    Will my build work - I am a beginner to Hackintosh

    When I type -v, the system reads alot of files and stops here. At this screen I cannot do much more. Was this the desired result? I have tried rebooting and it is pretty much statsu quo
  9. lassee

    Will my build work - I am a beginner to Hackintosh

    I'm not sure what verbose boot means. The screen turns "greywhite" with the Apple logo in the center. Earlier this screen flashed on the screen and the machine rebooted. After updating the bios, the picture now stays on the screen and the machine freezes instead of rebooting
  10. lassee

    Will my build work - I am a beginner to Hackintosh

    Thanks. Tried that. Now, instead of reboot, the computer freezes up and has the Apple logo on a white screen. :beachball:
  11. lassee

    Will my build work - I am a beginner to Hackintosh

    I have been trying to install OSX Mavericks with UniBeast using the guide on this site. I get to step 4 where I choose USB. After a few seconds I can see the Apple logo flash on the screen, and the system reboots. Any thoughts to what this might be caused by?
  12. lassee

    Will my build work - I am a beginner to Hackintosh

    Never mind. Figured it out :) I am new to MAC and new to making Hackintosh. So alot of new fun stuff for me :ugeek:
  13. lassee

    Will my build work - I am a beginner to Hackintosh

    So, finally my system is built and ready. Now I started using the guide on this site to setup unibeast and bootable USB. Well, since my iMac is not running OSX in english, the Unibeast says I need to change to english to proceed. Then shuts down. Any solution to this? :crazy:
  14. lassee

    Will my build work - I am a beginner to Hackintosh

    This is what I have ended up ordering: ASROCK Z87M Extreme4 - Socket 1150 Crucial Ballistix Sport XT 16GB 1866MHz Samsung 840 EVO Basic 500GB Intel Core i7-4790K Corsair Hydro H60 v2 Nvidia GeForce GTX 770 Bitfenix Phenom M White Corsair CX500w Modular BitFenix Spectre PRO...
  15. lassee

    Will my build work - I am a beginner to Hackintosh

    This is what I ended up ordering today. Hope I will have some success with this. Cool summer project for the old man :headbang: MB: ASROCK Z87M Extreme4 - socket 1150 RAM: Crucial Ballistix Sport XT 16GB 1866MHz SSD: 2xSamsung 840 EVO Basic 250GB CPU: Intel Core i7-4790K – Corsair Hydro H60 v2...
Back
Top