Recent content by EasyViber

Update didn't work for me. I've tried update trough App Store, but after update system is slow and I can't start most of Applications (Mail, Chrome, Terminal...) with "damaged or incomplete" error. :(

Under El Capitan my Photoshop CC 2015 crashed at startup without any error. It seems to be OpenCL problem. I've tryed LuxMark and it showed that CPU uses OpenCL, but GPU (Nvidia GTX 560ti) didn't. So I've added "nvda_drv=1" boot flag to clover (Nvidia injector is checked in my Clover) and...

Try with Multibeast 6.1.0: EasyBeast Realtek ALCxxx/Without DSDT/ALC887/888b Current v100302 I think i have ElliotForceLegacyRTC, EvOreboot, USB 3.0 - Universal, NullCPUPowerManegement, FakeSMC v5.3.820 Realtek - Lnx2Mac'2 RealtekRTL81xx v0.0.90 AppleACPIPlatform Rollback - 10.8.1 Rollback...

BridgeHelper removed NullCPUPowerManagement.kext, but Asus P8Z77-V LX doesn't work without it. It should work after you install NullCPUPowerManagement.kext.

I got my WD USB3 disk detected... but not always. Usually it gets detected if I turn it on and plug it after Lion was already working... and in this rare cases when it's detected, it works at usb3 speeds. But now I'm not sure what drivers are being used as I've installed ones from MB and some...

Eleron, could you post your DSDT and appleHDA? I couldn't get sound working with appleHDA.kext, it would crash while booting. I got some sounds (and some noise) using patched voodooHDA 2.7.2 but with no input and no front jacks. And even that stopped working after upgrading to 10.7.1 ;)

hi, I have similar configuration... my 560 ti started working after installing kext from http://www.kexts.com/view/1567-gtx_560_ ... .7_gm.html

another WD MyBook Essential USB3 not detected here. Tried on Asrock Z68 Pro3 with Etron (EJ168A?) chip. Using driver from mb.

I've got it working after restoring all kexts from Lion installation and repatching NVDAGF100Hal.kext. I won't touch that again if I don't have to.

Anyone got USB3 working?

most of us affected with this problem use nVidia cards with patched kexts so I would say we should look for problem there. Now I have dual screen system and in first two minutes I can move mouse but I can't move it to other screen. After about two minutes this happens (copied from console)...

I have/had same problem. First Lion boot goes fine, then I've removed ACPI_SMC_PlatformPlugin.kext (it caused some KP) and installed NVDAGF100Hal.kext from http://www.kexts.com/view/1567-gtx_560_ ... .7_gm.html I got my MSI 560 Ti Hawk working fine with all fancy accelerations, but with...

I've tried all that. I've written extended list of things I've tried but it got deleted from forum ;) I've managed to boot snow leo, and I've upgraded it to 10.6.8 But it only starts when I'm using "pmVersion=0" at boot. In other cases it restarts or even shuts down.

I get that when running installer. I've managed to run installer of certain distribution, but again I couldn't run anything after installation.

OK, I've filmed my boot so I can analyze what's going on. Last thing shown (while using -v -x) before restarting was: "Starting Darwin x86" But, maybe potential problem is few rows before? "ACPI table not found DSDT.aml"