- Joined
- Apr 27, 2013
- Messages
- 55
- Motherboard
- GA-H87N-WIFI v1.1
- CPU
- i3-4340
- Graphics
- HD 4600
- Mac
- Classic Mac
Hi. Not sure if I should post here, or elsewhere ?
I'm trying to solve an issue about USB3 HDDs plugged into the rear USB3 ports not mounting unless I use a USB2 Male>Female cable to "adapt / convert" the USB3 connection from the HDD to USB2.
I tried the FakePCIID.kext and FakePCIID_XHCIMux.kext, but the USB3 HDD was really slow.
Removed the FakePCIxxxxx kexts and with the USB3 > USB2 "adapter" the "speed"" of the USB3 HDD returned to normal (whatever that means) speeds.
I followed RehabMan's & PJALM's "instructions" (elsewhere) about using iasl
(iasl -da -dl DSDT.aml SSDT*.aml)
to generate a .dsl from the the DSDT.aml I generated via Clover bootloader using F4,
rather than using the System.DSDT from maciASL
I read through the iasl result output, but it might as well have been written in Ferengi, for all the good it did me to understand it .
When I patch the resulting DSDT.dsl in maciASL using Patch>Gigabyte>GA-H87N-Wifi, and then select Compile I get the following errors/warnings:
• Method Local is set but never used (Local3)
Which points to: Store (D0D3, Local3)
• Method Local is set but never used (Local0)
Which points to: Store (0x07D0, OSYS)
As I have absolutely no knowledge about the "Black Arts" of creating a DSDT.aml, I don't dare try the resulting output lest I "break things"
(I have been reading a lot of posts here on tonymacX86 and elsewhere about creating an DSDT, but I'm not going to pretend I even understand a fraction of them.... As much as I tried)
Can I ignore the warnings ? Or am I doing something completely wrong ? (far more likely)
my hardware is:
GA-H87N-Wifi with F9 bios, and an i3-4340 3.6Ghz.
ASMedia 1061 PCIe SATA Card (Both ports occupied/connected to HDDs)
Software is:
Clover v2.3 R4049
maciASL RM1.31 (252.3)
El Capitan 10.11.6
I've attached the iasl output and the DSDT file(s)
I'm trying to solve an issue about USB3 HDDs plugged into the rear USB3 ports not mounting unless I use a USB2 Male>Female cable to "adapt / convert" the USB3 connection from the HDD to USB2.
I tried the FakePCIID.kext and FakePCIID_XHCIMux.kext, but the USB3 HDD was really slow.
Removed the FakePCIxxxxx kexts and with the USB3 > USB2 "adapter" the "speed"" of the USB3 HDD returned to normal (whatever that means) speeds.
I followed RehabMan's & PJALM's "instructions" (elsewhere) about using iasl
(iasl -da -dl DSDT.aml SSDT*.aml)
to generate a .dsl from the the DSDT.aml I generated via Clover bootloader using F4,
rather than using the System.DSDT from maciASL
I read through the iasl result output, but it might as well have been written in Ferengi, for all the good it did me to understand it .
When I patch the resulting DSDT.dsl in maciASL using Patch>Gigabyte>GA-H87N-Wifi, and then select Compile I get the following errors/warnings:
• Method Local is set but never used (Local3)
Which points to: Store (D0D3, Local3)
• Method Local is set but never used (Local0)
Which points to: Store (0x07D0, OSYS)
As I have absolutely no knowledge about the "Black Arts" of creating a DSDT.aml, I don't dare try the resulting output lest I "break things"
(I have been reading a lot of posts here on tonymacX86 and elsewhere about creating an DSDT, but I'm not going to pretend I even understand a fraction of them.... As much as I tried)
Can I ignore the warnings ? Or am I doing something completely wrong ? (far more likely)
my hardware is:
GA-H87N-Wifi with F9 bios, and an i3-4340 3.6Ghz.
ASMedia 1061 PCIe SATA Card (Both ports occupied/connected to HDDs)
Software is:
Clover v2.3 R4049
maciASL RM1.31 (252.3)
El Capitan 10.11.6
I've attached the iasl output and the DSDT file(s)