DSDT for Z77 extreme 6

[MiniITX]

Hello MiniITX, I install the patched Bios, can you help me with the DSDT?

https://www.dropbox.com/s/jug307fnuq2cjyp/DSDT_JuaNiYoT_z77Extreme6 - Here is my DSDT.

Now I haven't sound through the GTX 560TI HDMI or jack of motherboard

1, Set the BIOS as per below.

Advance > Advanced\North Bridge Configuration
Primary Graphics Adapter > GPU*
Share Memory > 64MB*
Render Standby > Disabled*

Advanced\South Bridge configuration
Deep Sleep > Enabled in S5*

Advanced Storage Configuration
SATA Mode > AHCI*
Hard disk SMART > Enabled*

ADvanced\Super IO config > Serial Port - Disable

Advanced ACPI config
Suspend to RAM > Disabled*
ACPI HPET Table > Enabled*
RTC Alarm power on > by OS*
reset of the option here is disabled.

Not so imp settings but runs the system quite. Once you boot in fans are controlled by OSX.
HW Monitor
CPU FAN > Level 2
Chassis fan settings > Level 4

2, Fresh mountain Lion installation > http://www.tonymacx86.com/downloads.php?do=file&id=155

3, Download both DSDT and Broadcom 57781 unzip and keep on the desktop.

4, Download the tool Kext beast and run it. This will install the "Broadcom 57781.kext" > http://www.tonymacx86.com/downloads.php?do=file&id=32

5, Download Multibeast for Mountain Lion and run it with the below settings and reboot > http://www.tonymacx86.com/downloads.php?do=file&id=155





Update to 10.8.3 for smooth Graphics performance.
If you do the above steps correctly you should have a perfectly working hackintosh.

Ethernet kext credits > Mieze

-

 

[JuaNiYoT]

@MiniITX

Thanks a lot!

Now my Hackintosh boot very fast! (9 seconds and before 43 seconds aproximately!)

However when I update to 10.8.3, I can't boot it, but I can fix it disabling HD4000 in motherboard setting.

HDMI Audio don't fix, can you tell me what to do? I read the Toleda's guide but I don't understand what I must do.

 

[MiniITX]

Not sure why KP after upgrading to 10.8.3. Take a photo of KP and attach.

DSDT looks ok for HDMI Audio. After upgrading to 10.8.3 there is a good chance Audio kext was replaced with native audio kext.

Run the multibeast again with only the Audio option checked, reboot and check the HDMI Audio.

Make sure you select the HDMI option in System Preferences > Sound > Output

Also take a screenshot like below and attach.

 

[JuaNiYoT]

@MiniITX

KP and capture:

https://www.dropbox.com/sh/78qg9qdw4wcol4v/UrzhsNlL9G


To fix KP I must disable HD4000 and check Share Memory > Auto

For HDMI I put in audio setting all output options and nothing work for HDMI Audio

Thanks a lot!

Off topic:
This is ok? http://browser.primatelabs.com/geekbench2/1862920
I don't know if it is the normal xD

 

[Xelerater]

@JuaNiYoT

Friend there is an easy way to enable 560 ti HDMI Audio.. Just install VoodooHDA 0.2.61.kext using MultiBeast and reboot and then you will have to go to System Preferences -> Sound and there will be 4 HDMI Output options, just select the second one and you will have sound through 560 ti HDMI. Or try rest of the 4 HDMI Output options one of them may work for you, its better to give it a try. Let me know if it worked for you.

And use system definition iMac 13,1 for ivybridge not MacPro 3,1.

Regards,

 

[JuaNiYoT]

Don't work...

When I install VoodooHDA = KP...

I hope that MiniITX know the solution for the HDMI Audio

Thanks a lot, know I have iMac 13.1 and have 12149 in geekbench

 

[MiniITX]

Try the attached DSDT. Just replace the old DSDT with the new one in the Extra folder and reboot.

If the above doesn't work than flash the BIOS with patched BIOS version 2.4, extra the DSDT and attach.

http://biosrepo.wordpress.com/asrock/z77/

-

 

[JuaNiYoT]

Hello MiniITX, thanks for your help!

Don't work the HDMI audio...

I already have the patched bios, I don't understand what you want sorry. The only thing I can't put the same you tell me is the HD4000 options, because I must disable it for can boot the system...

Thanks for all

 

[MiniITX]

JuaNiYoT, i was talking about flashing the BIOS back to version 2.4. I am not sure why the HDMI audio not working. Best thing is to get help from experts > tolada

 

[kingd]

@MiniITX: Any suggestions for getting the USB 3 ports (etron ej168a) working?