sata

Hello all! I am pretty new to this type of build and this might be kind of a dumb question but let me explain what my situation is: I recently installed OS X Yosemite and following that install I used multibeast to get the boot to work. After awhile I decided to install my eSATA ports into my...

Attempting new install of El Capitan to new hardware. GA-Z97-HD3 (latest F9 BIOS). Created Clover boot drive following El Capitan setup Guide on this site, setup bios according to http://www.tonymacx86.com/user-builds/154879-success-ga-z97-hd3-i7-4790k-gtx-970-16gb-yosemite-10-10-1-a.html WD...

Hi I Installed Mavericks 10.9.4 on Lenovo D20 using Clover https://support.lenovo.com/us/en/documents/migr-72304 http://www.lenovo.com/shop/americas/content/pdf/thinkstation/thinkstation__s20-d20_oct-2010.pdf but i have a problem with Sata Ports Mac wont boot with blue ports "5 Ports Hard...

[RESOLVED]Clover boot issues after moving external USB HDD to internal SATA slot Hi guys, I installed Yosemite 10.10.4 on my pc with the following specs: GA-Z97HD3 Core i5 4690 8GB Crucial RAM Radeon R9 290 4GB SATA MODE AHCI 640 GB WD HDD 256 GB Crucial SSD + 1TB HDD (not used for OS X, only...

FIXED: SATA Operation AHCI Not Saving in Bios FIXED! Look below I have a Dell Optiplex 780 with a solid state hard drive and have successfully installed 10.10 on it. Only issue i'm having is every time I boot I have to go to the bios and change the SATA Operation to AHCI. It for some reason...

Hello, I have a Gigabyte H81M-H motherboard with the i5-4690 processor with a fully functional hackintosh installation. Recently, I booted up my system and then faced this error multiple times AFTER passing the Chimera screen: EBIOS read error: Controller or device error Block 0x0 Sectors...

http://imgur.com/BuucUqH,iGgSLtJ Above are two screenshots, one of a BlackMagic SpeedTest, and another of my SATA section from system report... :( Anyone know how to fix these slow write speeds? I was expecting more from a Kingston 120 GB SSD...

Hello, I created a UniBeast USB with OS X Mavericks. But when I want to install OS X, there are no drives in Disk Utility, I can only see my USB. My computer is a Dell Dimension E520. Processor: Intel Core 2 Quad Q6600 RAM: 3 GB Graphics card: ATI Radeon HD 5450 Hard drive: 200 GB SATA How...

I created a 10.10 installer with the Legacy USB option and I can successfully boot to the installer with boot flags -x GraphicsEnabler=Yes. My hard drive is not recognized in disk utility and the system report says there are no SATA devices. I partitioned it as GUID and formatted HFS+ on...

I have a Gigabyte Z68XP-UD3 that I am trying to upgrade to Yosemite. I was running Mavericks successfully with the F10 BIOS. I upgraded to U1J EFI today in preparation for Yosemite. My Mavericks install will no longer boot with EFI - it kernel panics immediately. So, onto Yosemite... I set up...

Hi there, I've looked and searched through the forums and I haven't been able to pin down the exact cause of this issue. As you can see, my read and write speed are absurdly low. It could be due to the SATA ports I'm connected to. But I'm not advanced enough to know the difference between...

Hey everybody, since my mainboard has two raid modes (one with the internal Z87 chipset and one with Marvell® 88SE9172 chip), I was wondering of someone has tested this feature. My main goal is to set a RAID 0 and get fast disks to work together. Reading the manual I understand that is has to...

Hey there I'm running 10.9.2 on a H61N-usb3. The mobo has 2 SATA connections, i've used one for the boot drive which is a 3.5" SATA and I've plugged the other SATA port in with another 3.5 SATA drive, but it's never recognized or mounted. I've checked on disk utility and the disk doesn't...

My mobo of Gigabyte GA-Z77X-UP4 TH has 6 SATA ports, which I thought would be enough. However, the mSATA drive slot on the mobo is on the same bus as the 6th SATA port, so I can only use one or the other (plugging in an mSATA disables the 6th SATA port). To get around this issue, I figured...

Hiya, I need a preferably cheap non RAID 4 port SATA controller that is compatible with Mavericks and Windows 7/8.1. I would really appreciate some advice since I have like 3 different controllers here and none of them work with the hackintosh. I'm reluctant to increase the size of my...

I changed the SATA Operation, but I'm still with this problem, I can't boot mavericks or snow leopard because that, what can I do ?

I've recently obtained a Dell Latitude E6400 from a friend and I'm trying to install Mavericks on it with Unibeast but it keeps hanging at the Apple logo. I've gone through the BIOS and set everything to how it should, according to the internet, but I keep running into an issue with the SATA...

I have installed Mac OS X 10.6.0 on my PC but i have run MultiBeast 3.10.1 but i get boot0 errors all the time. I am happy to always use iBoot but I have found that the SATA configuration must be set to AHCI Mode for OS X but SATA Mode for Windows 7. is there any way i can allow it to boot both...

Amazon has a few two port SATA mini PCIe cards available and I was wondering if anyone had replaced the wifi/BT mini card with a SATA one? Everything should work, but I was wondering if someone tried it already. Thanks.

Hey guys, I'm looking for a PCIE card that will allow me to connect 4 SATA drives (preferably SATA III) internally. I'm specifically working with a Gigabyte Z77 DS3H. Does anyone know of any that work natively?