[Guide] Intel Skylake NUC6 (and Skull Canyon) using Clover UEFI (NUC6i5SYK, NUC6i7KYK, etc)

[den_breacker]

Problem seems obvious. Your system volume is named 'macOS HD', but you're telling Clover via config.plist/Boot/DefaultVolume to look for 'MacOS HD'.

Hmm, lame
Thanks !

 

[den_breacker]

It is covered in the README: https://github.com/RehabMan/patch-nvme

I can't figure it out :s
I deleted nvmegeneric.kext from efi/clover/other. I ran the nvme-patch. Next I installed the Hack.kext to S/L/E zith Easykext Pro. After that, my system froze and rebooted. Now I'm stuck at the apple logo...
Can you help please ?

 

[RehabMan]

I can't figure it out :s
I deleted nvmegeneric.kext from efi/clover/other. I ran the nvme-patch. Next I installed the Hack.kext to S/L/E zith Easykext Pro. After that, my system froze and rebooted. Now I'm stuck at the apple logo...
Can you help please ?

If you had NVMeGeneric.kext in EFI/Clover/kexts/Other when you ran install_downloads.sh, NVMeGeneric.kext is now also installed to /L/E. So you need to be certain to remove it from there (you cannot have both NVMeGeneric and the HackrNVMeFamily installed at the same time). If you have HackrNVMeFamily-*.kext in EFI/Clover/kexts/Other, install_downloads.sh will install it to /L/E.

You may need to boot to the OS X installer, and use Terminal to fix your situation with NVMeGeneric.kext/HackrNVMeFamily/etc.

 

[den_breacker]

If you had NVMeGeneric.kext in EFI/Clover/kexts/Other when you ran install_downloads.sh, NVMeGeneric.kext is now also installed to /L/E. So you need to be certain to remove it from there (you cannot have both NVMeGeneric and the HackrNVMeFamily installed at the same time). If you have HackrNVMeFamily-*.kext in EFI/Clover/kexts/Other, install_downloads.sh will install it to /L/E.

You may need to boot to the OS X installer, and use Terminal to fix your situation with NVMeGeneric.kext/HackrNVMeFamily/etc.

Ok, solved. Thank you very much

 

[snipebase]

Not working:
- DP and HDMI at the same time is not working (eg. no multiple monitors)

What's the status for this "issue"? Is this going to work? I hesitate to buy these NUC but I really need multiple monitors (1 x 4K & 1 x 1080P).

Thanks for the great work!

 

[RehabMan]

What's the status for this "issue"? Is this going to work? I hesitate to buy these NUC but I really need multiple monitors (1 x 4K & 1 x 1080P).

Thanks for the great work!

Multiple monitors work ok with iMac14,1 SMBIOS. Hotplug is a bit unreliable.
I have no 4k hardware (early adopter penalty still to large).

 

[superslurt]

Thank you so much for providing this easy and extensive guide. Finally my Skull Canyon is a usable hackintosh. The only issue so far is that it once turned itself off randomly. But it booted fine afterwards, and haven't done it since.

 

[picchitta]

I put the problem reporting in message 165 because I have no audio output in hdmi/dp port.
Did you find some problem? Of course it is not urgent.

Read post #1, "Problem Reporting".

Make sure you include information on the physical ports (HDMI/DP) your NUC6 has.

Here Problem reporting, I hope I did not forget anything.

 

[RehabMan]

I put the problem reporting in message 165 because I have no audio output in hdmi/dp port.
Did you find some problem? Of course it is not urgent.

I will try and compare against my own later, but for now you should check that you have it enabled in BIOS.

 

[den_breacker]

Multiple monitors work ok with iMac14,1 SMBIOS. Hotplug is a bit unreliable.
I have no 4k hardware (early adopter penalty still to large).

I'm able to get multiple monitors working by booting with one monitor connected and then hotplugging the other one. Booting with 2 monitors did not work for me.
But with 2 monitors connected, I think sleep isn't working properly anymore. Wasn't able to wake the NUC up, had to hard reboot.
Is there a workaround for getting sleep to work ?