USB ports only recognize USB2 devices?

[BDubs]

Hi all, pretty new here! I have seen some info on this situation, but nothing I have tried has worked for me so far.

I just built a hackintosh and have basically everything working finally - except all my USBports (case and MB) will only recognize a USB 2.0 device - my USB3 devices receive power, but never appear in macOS, including not being under System info USB.

I have already tried using FakePCIID.kext methods. My IOACPIPlane is attached in a screenshot, I believe it recognizes all of my ports?

At this point, I am just very lost and unsure how to proceed. Any help is greatly appreciated! I will happily provide any info needed as quickly as I can.

Phanteks Enthoo Evolv
Asus TUF Z270 Mk.1
i7 6700
2x16gb Ballistix Sport LT
GTX 1080 Founders
macOS Sierra 10.12.4 -- 14,2

 

[RehabMan]

Hi all, pretty new here! I have seen some info on this situation, but nothing I have tried has worked for me so far.

I just built a hackintosh and have basically everything working finally - except all my USBports (case and MB) will only recognize a USB 2.0 device - my USB3 devices receive power, but never appear in macOS, including not being under System info USB.

I have already tried using FakePCIID.kext methods. My IOACPIPlane is attached in a screenshot, I believe it recognizes all of my ports?

At this point, I am just very lost and unsure how to proceed. Any help is greatly appreciated! I will happily provide any info needed as quickly as I can.

Phanteks Enthoo Evolv
Asus TUF Z270 Mk.1
i7 6700
2x16gb Ballistix Sport LT
GTX 1080 Founders
macOS Sierra 10.12.4 -- 14,2

https://www.tonymacx86.com/threads/guide-10-11-usb-changes-and-solutions.173616/

 

[BDubs]

https://www.tonymacx86.com/threads/guide-10-11-usb-changes-and-solutions.173616/

Thanks, I have tried the following from it and still have not gotten it working - BIOS Config, Disabling Default Injectors, Installed FakePCIID_XHCIMux & FakePCIID.

I am feeling pretty lost past that point in the guide, which is why I originally attached the screen from my IOACPIPlane. I'm not sure how to properly proceed from here. Is there anything specific you recommend?

Thanks so much

 

[RehabMan]

Thanks, I have tried the following from it and still have not gotten it working - BIOS Config, Disabling Default Injectors, Installed FakePCIID_XHCIMux & FakePCIID.

I am feeling pretty lost past that point in the guide, which is why I originally attached the screen from my IOACPIPlane. I'm not sure how to properly proceed from here. Is there anything specific you recommend?

Thanks so much

FakePCIID_XHCIMux.kext has no application to your hardware (and it says so in the guide...). 100-series and 200-series have no EHCI controller...

And you didn't mention XHCI-200-series-injector.kext...

I think you should read the guide again...

 

[BDubs]

FakePCIID_XHCIMux.kext has no application to your hardware (and it says so in the guide...). 100-series and 200-series have no EHCI controller...

And you didn't mention XHCI-200-series-injector.kext...

I think you should read the guide again...

I apologize, easy to miss things in such a big guide - I am very very new to Hackintosh.

I installed the XHCI-200 kext and added in the 2 recommended patches. Upon reboot, my drives still were not appearing - and for some strange reason, my audio had stopped working. I removed the 2 patches, and my audio came back after the next reboot.

After that 2nd reboot, some of my ports are working. One of my 2 front ports is working (although, it is very slow to mount). The other one still won't recognize. The rear USB2 ports all work as well as the single USB3.1. The 2 rear USB3 ports though do not read still.

I will continue to experiment and hopefully find a detail I missed in that guide, thank you for helping

 

[RehabMan]

I apologize, easy to miss things in such a big guide - I am very very new to Hackintosh.

I installed the XHCI-200 kext and added in the 2 recommended patches. Upon reboot, my drives still were not appearing - and for some strange reason, my audio had stopped working. I removed the 2 patches, and my audio came back after the next reboot.

After that 2nd reboot, some of my ports are working. One of my 2 front ports is working (although, it is very slow to mount). The other one still won't recognize. The rear USB2 ports all work as well as the single USB3.1. The 2 rear USB3 ports though do not read still.

I will continue to experiment and hopefully find a detail I missed in that guide, thank you for helping

If you're using an AppleHDA injector (such as realtekALC.kext), missing audio upon installing new kexts is a common/expected problem (you need to boot without caches, rebuild cache... and reboot)

If you have an issue, read guide, post #1, "Problem Reporting".