Contribute
Register

[GUIDE] Mountain Lion 10.8.2 Lenovo T410 Intel HD Graphics

Status
Not open for further replies.
uuujour said:
Excuse my questions.
I could success to install Mountain Lion into my T510, but it has few problems.

My Laptop
Model: Lenovo/ThinkPad T510 15.6 inch
CPU: Intel i7 M620 (2.66Ghz)
GPU: Intel HD Graphics
WiFi: AR9280
Display: 15.6 inch 1920x1080, (AUO display, exchanged by myself)
RAM: 8G(4GBx2) DDR3 1333mhz
HDD: 1TB
BIOS: v1.51 mod BIOS

#1 Can not change the display resolution from 1024x768.
I know the problem of 1st Gen IntelHD Graphics. I followed this Tips "[GUIDE] 1st Generation Intel HD Graphics QE/CI", but it seems to be unable the CI. (Screen Saver of the slideshows is not working, but Flurry is ok)

#2 Sleep is not working?
Display became gray-out when the laptop sleep, but it can be recovered to normal condition.
Is it normal for the any x86Mac?

View attachment 115644View attachment 115645

Thank you for your kindness.
Click to expand...

Sleep requires properly working graphics. Follow the link for 1st gen HD -- it is the best out there.

Don't expect sleep to work without properly enabled QE/CI and CPU power management working...
 
klaus65 said:
Hello.

Does Atheros AR5B93 works in Lenovo T410 with a half size/full size adapter?

Is this wificard locked in BIOS?

Thanks and Regards
Click to expand...

You should check this post for example, and I think you have to apply MOD BIOS.
MOD BIOS is also shown follow post with download link.
 
RehabMan said:
Sleep requires properly working graphics. Follow the link for 1st gen HD -- it is the best out there.

Don't expect sleep to work without properly enabled QE/CI and CPU power management working...
Click to expand...
Thank you, Mr RehabMan. I try QE/CI setting again.
I want to ask you to be sure. Does the problem of display resolution can be solved when correct setting was done?

Sincerely yours,
 
uuujour said:
Thank you, Mr RehabMan. I try QE/CI setting again.
I want to ask you to be sure. Does the problem of display resolution can be solved when correct setting was done?

Sincerely yours,
Click to expand...

Yes.
 
erere2 said:
EDIT: SOLVED THE PROBLEM BY DELETING THE CORRECT FILES OF THE USB.
Apperantly I deleted AppleHD* not AppleIntelHD*


Thanks for the GUIDE.
I've tried it but I'm facing an issue where I'm stuck at boot as shown below.
View attachment 47321

I waited for hours but it doesn't go forward from this point. :beachball:
I've tried booting with "-v npci=0x2000" , "-v" , "-x" none of them worked.
I have a Lenovo T410 with Intel HD Graphics.
My BIOS version is v1.34 (same as in the GUIDE)
I've also tried enabling/disabling Virtualization beucase just loading default config in BIOS settings doesn't change Virtualization.

Any idea what can be the cause of this?​
Click to expand...

My T410 has i5 540M and with Intel HD Graphics.
I am trying to install mountain lion on it.
I created usb with unibeast and deleted the AppleIntelHD*, AppleIntelFrame* and AppleIntelSNB.
I got the same issue as you.
What can I do? anybody can help me?
 
fisk said:
Thanks! :)
I am now writing this from my T410 with Intel HD graphics.
I did have some problems getting the resolution right (1440x900), but found this post which solved it:
http://www.tonymacx86.com/graphics/85172-1st-gen-intel-hd-graphics-native-resolution.html
Obviously the Intel WLAN does not work, but I'm fine with wire.


Brightness controls not working here.
Click to expand...

Thanks for sharing. and May I ask a question? are your setting and kernels suitable for t410s?
I have a notbook of t410s, i5-m520 and Integrated HD graphics. 1440X900. motherboard chip-set is QS57.
Thank you very much!
Tom
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top