Contribute
Register

[SUCCESS][Catalina 10.15.3]Gigabyte Z370 HD3/Intel-Core i3 8100

Joined
Jul 11, 2018
Messages
4
Motherboard
Gigabyte Z370 HD3 (rev. 1.0)
CPU
Intel Core i3-8100 Box
Graphics
Intel UHD Graphics 630
Hi everyone ! This is my first post, i begin hackintosh with this build with High Sierra. After with Mojave , and now i decide to post this build with Catalina. There they are the steps that i make to setup Catalina with last update and all works perfectly!

First of all BIOS settings are the classics, VD-T disable etc

Step 1: I make a bootable usb stick with Unibeast for Catalina
Step 2: I install mac os with no extra drivers
Step 3: Once you get in Mac , download multibeast for Mojave (yes it works, from there you can take drivers for native audio support)
and Clover Configurator
Step 4: Open Clover Configurator and from the list left, select Mount EFI both for usb and your Mac OS disk. Then delete EFI folder from your MacOS drive and replace it with EFI folder from your usb stick. Then, inside your CLOVER folder there is a file "config.list", open it with clover configurator to set up UHD graphics acceleration. Once you open see my screenshots what i have check and do the same. Save and Exit . And Finally
Step 5: Open Multibeast for Mojave and select: Drivers-->Audio-->AppleALC and Optional 3 port (native)audio and click build and install
Reboot your system and all must works correctly

I hope this post help you :)
 

Attachments

Joined
Mar 12, 2012
Messages
3
Motherboard
Gigabyte Z370 HD3
CPU
i5 8400
Graphics
Intel UHD Graphics 630
Mac
MacBook Air, MacBook Pro
Mobile Phone
iOS
Hi! Whats your bios version?, I cant get through the installer's loading screen
 
Joined
Jul 11, 2018
Messages
4
Motherboard
Gigabyte Z370 HD3 (rev. 1.0)
CPU
Intel Core i3-8100 Box
Graphics
Intel UHD Graphics 630
Hi, I didn’t update it, it is the version that comes from the factory
Make sure that all bios settings are correct to proceed to the installation
 
Joined
Apr 17, 2020
Messages
3
Motherboard
Gigabyte Z370 HD3
CPU
i3 8100
Graphics
RX580
Hello! Having the exact same specs. I'm also stuck in the installer's loading screen, loads to the end then hangs .. Any help ? :roll2:

BIOS settings:
-Windows 8/10 WHQL (There is no Other OS)
-CSM support Disabled
-Super IO Configuration both Serial Port and Parallel Port Disabled
-XHCI Hand-off Enabled
-SATA Mode Selection set to AHCI
-VT-d Disabled
-DVMT Pre-allocated 64M
-DVMT Total Gfx Mem 256M
 
Joined
Jul 11, 2018
Messages
4
Motherboard
Gigabyte Z370 HD3 (rev. 1.0)
CPU
Intel Core i3-8100 Box
Graphics
Intel UHD Graphics 630
First make sure that you have made usb stick with unibeast
Second there is other os Choise
Check on YouTube gigabyte motherboard hackintosh settings
if you have the same specs with me it will work
 
Joined
Mar 26, 2020
Messages
3
Motherboard
Gigabyte z370hd3
CPU
i3 9100f
Graphics
rx580 8gb
Hi! Whats your bios version?, I cant get through the installer's loading screen
Hi, the las time was using a hackintosh pc, can't install Mojave, I just give up cuz can't boot, always in black screen, and now with Catalina, with this post can't boot but, the bios version is 13, there is a new one 14b, in another post recomended version 10, after a bios downgrade, finally boot and install Catalina, but my processor is a 9100F no graphics and a AMD RX580 8GB, Catalina already have RX580 kext so boot with native video kext and if I change with Clover the options like in the screenshots, after boot lost video, I know is because is for a processor with integrated graphics, so decide to copy de efi folder of usb to ssd without touch, can boot, can use, lan, video and audio is on DP port, not use internal audio have to try like Tsimo recomended, and I wanna know if is necesary to do change in config.plist because I like to reinstall High Sierra in a Asus Maximus IV, the last usb I use for boot, can't make it in this Catalina, like if have some problems with usb even to format usb is something slow, even clover take some time to boot in ssd and can see another partition name filevault prebooter, the last time I use hackintosh in the z370HD3 was High Sierra and a i3 8100, so what options have to use in config.plist to have everything working, thx and sorry for a very very bad english
 
Joined
Mar 26, 2020
Messages
3
Motherboard
Gigabyte z370hd3
CPU
i3 9100f
Graphics
rx580 8gb
Hi, the las time was using a hackintosh pc, can't install Mojave, I just give up cuz can't boot, always in black screen, and now with Catalina, with this post can't boot but, the bios version is 13, there is a new one 14b, in another post recomended version 10, after a bios downgrade, finally boot and install Catalina, but my processor is a 9100F no graphics and a AMD RX580 8GB, Catalina already have RX580 kext so boot with native video kext and if I change with Clover the options like in the screenshots, after boot lost video, I know is because is for a processor with integrated graphics, so decide to copy de efi folder of usb to ssd without touch, can boot, can use, lan, video and audio is on DP port, not use internal audio have to try like Tsimo recomended, and I wanna know if is necesary to do change in config.plist because I like to reinstall High Sierra in a Asus Maximus IV, the last usb I use for boot, can't make it in this Catalina, like if have some problems with usb even to format usb is something slow, even clover take some time to boot in ssd and can see another partition name filevault prebooter, the last time I use hackintosh in the z370HD3 was High Sierra and a i3 8100, so what options have to use in config.plist to have everything working, thx and sorry for a very very bad english
Well, if I open Multibeast for Mojave and select: Drivers-->Audio-->AppleALC and Optional 3 port (native)audio or use others options, when reboot and Mac logo appear, some weird lines show and video go to sleep, after some test this is my report, in Clover configurator use kext injector and upgrade/download Lilu, Whatevergreen, AppleALC, fakeSMC sensor and change Mac model data to 18,2 and fill all the data need it same Rt values, change ig-platform-id to 0x59120003 and fix shutdown, all this in EFI folder of the usb created with Unibeast Catalina and copied to EFI in SSD, now have sound in DisplayPort and internal audio (still don't know how to enable 5.1 ports) RX580 still the same no problem, USB 2.1-3.1 working fine (Unibeast have some problems with Kingston usb to create usb installer, AData work fine), just don't know if still have to change more values on config.plist because still have High Sierra file and have more options but is working fine, can use everything even FaceTime (Lenovo T24v-10 Display integrated webcam) and AppleTV, very happy on this Hackintosh, thx for this post (btw use bios version 10)
 

Attachments

Joined
Apr 17, 2020
Messages
3
Motherboard
Gigabyte Z370 HD3
CPU
i3 8100
Graphics
RX580
My problem was the F12 BIOS. I put F10 on it and runs good now.. Took me a while
 
Joined
Apr 17, 2020
Messages
3
Motherboard
Gigabyte Z370 HD3
CPU
i3 8100
Graphics
RX580
Hi everyone ! This is my first post, i begin hackintosh with this build with High Sierra. After with Mojave , and now i decide to post this build with Catalina. There they are the steps that i make to setup Catalina with last update and all works perfectly!

First of all BIOS settings are the classics, VD-T disable etc

Step 1: I make a bootable usb stick with Unibeast for Catalina
Step 2: I install mac os with no extra drivers
Step 3: Once you get in Mac , download multibeast for Mojave (yes it works, from there you can take drivers for native audio support)
and Clover Configurator
Step 4: Open Clover Configurator and from the list left, select Mount EFI both for usb and your Mac OS disk. Then delete EFI folder from your MacOS drive and replace it with EFI folder from your usb stick. Then, inside your CLOVER folder there is a file "config.list", open it with clover configurator to set up UHD graphics acceleration. Once you open see my screenshots what i have check and do the same. Save and Exit . And Finally
Step 5: Open Multibeast for Mojave and select: Drivers-->Audio-->AppleALC and Optional 3 port (native)audio and click build and install
Reboot your system and all must works correctly

I hope this post help you :)

All went well except the fact that the LAN port is not recognised by Mojave. Any idea what to do ?
 
Joined
Mar 26, 2020
Messages
3
Motherboard
Gigabyte z370hd3
CPU
i3 9100f
Graphics
rx580 8gb
All went well except the fact that the LAN port is not recognised by Mojave. Any idea what to do ?
Runing Catalina but, I don't remember if in Mojave recognised the LAN port, in High Sierra at start have LAN, same in Catalina, in the screenshot is the model on chip, and the kext I runing on it, hope can help.
 

Attachments

Top