Contribute
Register

[NoSuccess] Lifebook T904 working Files

Status
Not open for further replies.
Config.plist is from here: https://github.com/RehabMan/OS-X-Clover-Laptop-Config/blob/master/config_HD4600_4400_4200.plist
added SMBIOS and graphics id information as described in guide.

No need to modify SMBIOS for the installer. Such tweaks are post-install tasks.

The EFI/Clover in post #1, as already stated, does not conform to the guide... I'm ignoring it.
Expected that you attach new EFI/Clover that actually corresponds to guide instructions.

Also, make sure you fill out your profile to include Clover info too (especially since you have failed to provide an EFI/Clover with misc/preboot.log). Otherwise, I'm assuming you're booting UEFI (it would be confirmed by misc/preboot.log).
 
and attached preboot.log (think this You missed).

No.
Look at the files YOU attached (no misc/preboot.log there).

You should verify this memory information is correct (from preboot.log):
Code:
0:100  0:000  === [ Get Smbios ] ========================================
0:100  0:000  Type 16 Index = 0
0:100  0:000  Total Memory Slots Count = 2
0:100  0:000  Type 17 Index = 0
0:100  0:000  Ignoring insane frequency value 0MHz
0:100  0:000  SmbiosTable.Type17->Speed = 0MHz
0:100  0:000  SmbiosTable.Type17->Size = 0MB
0:100  0:000  SmbiosTable.Type17->Bank/Device = BANK 0 Onboard
0:100  0:000  SmbiosTable.Type17->Vendor = <null string>
0:100  0:000  SmbiosTable.Type17->SerialNumber = <null string>
0:100  0:000  SmbiosTable.Type17->PartNumber = <null string>
0:100  0:000  Type 17 Index = 1
0:100  0:000  SmbiosTable.Type17->Speed = 1600MHz
0:100  0:000  SmbiosTable.Type17->Size = 4096MB
0:100  0:000  SmbiosTable.Type17->Bank/Device = BANK 2 DIMM1
0:100  0:000  SmbiosTable.Type17->Vendor = Micron
0:100  0:000  SmbiosTable.Type17->SerialNumber = 56676188
0:100  0:000  SmbiosTable.Type17->PartNumber = 8KTF51264HZ-1G6E1 
0:100  0:000  Boot status=0
0:100  0:000  Running on: 'LIFEBOOK T904' with board 'FJNB27A'

Note, trying to use multiple plists is a mistake. You should have only one plist, must be named config.plist.
Code:
0:107  0:000  === [ Found config plists ] ===============================
0:107  0:000  - config.plist
0:107  0:000  - config_05.plist
0:107  0:000  - config_06.plist
0:107  0:000  - config_rehabman_t904.plist

This set of drivers64UEFI files is not correct:
Code:
0:108  0:000  === [ LoadDrivers ] =======================================
0:108  0:000  Loading AppleImageCodec-64.efi  status=Success
0:108  0:000  Loading HFSPlus.efi  status=Success
0:109  0:000   - driver needs connecting
0:109  0:000  Loading AppleUITheme-64.efi  status=Success
0:109  0:000  Loading DataHubDxe-64.efi  status=Success
0:138  0:029  Loading AppleKeyAggregator-64.efi  status=Success
0:139  0:000  Loading AptioInputFix.efi  status=Success
0:140  0:000  Loading FSInject-64.efi  status=Success
0:140  0:000  Loading FirmwareVolume-64.efi  status=Success
0:141  0:000  Loading SMCHelper-64.efi  status=Success
0:141  0:000  Loading apfs.efi  status=Success
0:143  0:001   - driver needs connecting
0:143  0:000  Loading UsbKbDxe-64.efi  status=Success
0:143  0:000   - driver needs connecting
0:143  0:000  Loading UsbMouseDxe-64.efi  status=Success
0:144  0:000   - driver needs connecting
0:144  0:000  Loading PartitionDxe-64.efi  status=Success
0:144  0:000   - driver needs connecting
0:144  0:000  Loading Fat-64.efi  status=Success
0:144  0:000   - driver needs connecting
0:144  0:000  Loading OsxFatBinaryDrv-64.efi  status=Success
0:145  0:000  Loading AptioMemoryFix.efi  status=Success
0:146  0:000  6 drivers needs connecting ...
0:146  0:000  PlatformDriverOverrideProtocol not found. Installing ... Success
0:146  0:000  Partition driver loaded: 
0:146  0:000  HFS+ driver loaded
0:146  0:000  APFS driver loaded
0:146  0:000  Searching for invalid DiskIo BY_DRIVER connects: not found, all ok
 
I already uploaded the required ZIP at #1. Now attached the little modified clover.
Preboot has been attached from me at #18 but now also included.
 

Attachments

  • t904_bios-1.17_clover-4458_v2.zip
    3.2 MB · Views: 57
I already uploaded the required ZIP at #1. Now attached the little modified clover.
Preboot has been attached from me at #18 but now also included.

Problems:
- Your config.plist is not from my guide (it has been modified incorrectly)
- you are not using the RehabMan clover (see link in guide)
- drivers64UEFI is not per guide (please read the guide carefully)
- kexts/Other is not per guide (do not use kexts not recommended in the guide)

Note: With older hardware such as yours, you will probably need OsxAptioFixDrv-64.efi, not AptioMemoryFix.efi. You should eliminate unnecessary *.efi files not recommended by the guide.
 
Now I tried to do all as described but need help at

Note: HD4200, HD4400, and HD4600 on 10.10+ needs special patches/injections, thus the separate config_HD4600_4400_4200.plist.
. Can You please make these injections to Your HD4400-config and send me?
 
Attached the current clover including new origin, preboot.log and sorted kexts / drivers according to guide, but plist without injections.
 

Attachments

  • t904_guide_01.zip
    1.6 MB · Views: 64
Attached the current clover including new origin, preboot.log and sorted kexts / drivers according to guide, but plist without injections.

I don't know what you mean by "plist without injections".
The guide does not recommend OsxAptioFix3Drv-64.efi.

You failed to provide any information regarding the problem.
 
Thought OsxAptioFix3Drv-64.efi is newer Version...
So now I will try with older OsxAptioFixDrv-64.efi.

Meant as quoted: In Guide You say: Config "needs special patches/injections" for HD4400. I do not know how to realize such patches or injections so my config is without them at the moment.

Problem is still KP or stuck at "+++++++++++++++++++++++++++++++++++"

Photos will follow, preboot.log already included in ZIP from last #26.
 
Thought OsxAptioFix3Drv-64.efi is newer Version...
So now I will try with older OsxAptioFixDrv-64.efi.

Guide recommends AptioMemoryFix.efi as a first try, then OsxAptioFixDrv-64.efi, then others.

Meant as quoted: In Guide You say: Config "needs special patches/injections" for HD4400. I do not know how to realize such patches or injections so my config is without them at the moment.

Special injections are already in the provided plists.
Also HD4400 requires FakePCIID.kext + FakePCIID_Intel_HD_Graphics + Lilu.kext + IntelGraphicsFixup.kext.

Problem is still KP or stuck at "+++++++++++++++++++++++++++++++++++" photo will follow.

That symptom has various causes...

No "Problem Reporting" files attached.
Read FAQ, "Problem Reporting" again. Carefully. Attach all requested files/output.
https://www.tonymacx86.com/threads/faq-read-first-laptop-frequent-questions.164990/
 
these are the photos when using AptioMemoryFix:
 

Attachments

  • 20180518_212949.jpg
    20180518_212949.jpg
    2.3 MB · Views: 49
  • 20180518_211704.jpg
    20180518_211704.jpg
    2.6 MB · Views: 60
Status
Not open for further replies.
Back
Top