<< Solved >> [Need Help] Mojave installation with USB 3.0 port

[fyritp]

Hi, i have a problem on getting Mojave installer working with my laptop,it always shows the AppleUSBXHCIPort::resetAndCreateDevice: failed to start device Error and then show a prohibited symbol.


I have only 2 USB 3.0 ports on my laptop i don't have USB 2.0,

* so i tried injecting XHCI-300-series-injector.kext and USBInjectAll.kext and XHCI-unsupported.kext, didn't work


* i even tried Increasing Max Port Limit with Multibeast didn't work either


* finally i tried the patching method Port limit Remover patch with Clover Configurator with the lanes of v10.14.4 in the list of patches didn't work so i tried again with new lanes from DallanSky ydeng and PMHeart:

com.apple.iokit.IOUSBHostFamily 83FB0F0F 83FB3F0F
USB port limit patch #1 10.14.x modify by DalianSky(credit ydeng) 10.14.x

com.apple.iokit.IOUSBHostFamily 83E30FD3 83E33FD3
USB port limit patch #2 10.14.x modify by DalianSky(credit PMHeart) 10.14.x

com.apple.driver.usb.AppleUSBXHCI 83FB0F0F 83FB3F0F
USB port limit patch #2 10.14.x modify by DalianSky(credit PMHeart) 10.14.x

com.apple.driver.usb.AppleUSBXHCI 83FF0F0F 83FF3F0F
USB port limit patch #2 10.14.x modify by DalianSky(credit PMHeart) 10.14.x


And all of that didn't work, i've seen somewhere to try a USB 2.0 Hub and connect it ot my USB 3.0 port but didn't try it yet

If there is someone that have a solution for that problem, hope you could help me with this.

 

[fyritp]

no one can help?

 

[Feartech]

no one can help?

make sure to use a usb2.0 stick, try all your usb3.0 ports

zip and upload your clover folder if that fails

 

[P1LGRIM]

hope you could help me with this

What size is your flash drive ?
Must be less than 32GB or create a partition of 32GB or less.

 

[fyritp]

make sure to use a usb2.0 stick, try all your usb3.0 ports

zip and upload your clover folder if that fails

Already did this didn't work, i'm using a USB 2.0 flash

 

[Feartech]

Already did this didn't work, i'm using a USB 2.0 flash

zipped clover folder?

 

[fyritp]

What size is your flash drive ?
Must be less than 32GB or create a partition of 32GB or less.

it's only 16GB

 

[fyritp]

zipped clover folder?

upload it here?

 

[fyritp]

zipped clover folder?

Here it is

 

[Feartech]

Here it is

NullCPUPowerManagement.kext should not be used, not sure where you read on using that

should only be one folder in kexts called "other" remove the rest of the folders and have your essential kexts in other folder

drivers64UEFI folder you have OsxAptioFix3Drv-64 and OsxAptioFixDrv-64, wrong, you only need one of those in there

config.plist is not from the guide

go back and start again:

[Guide] Booting the OS X installer on LAPTOPS with Clover

Overview One of the first challenges you'll face in installing OS X to your laptop will involve getting the OS X installer to boot from USB. This guide is for those wishing to use Clover (and in fact the only bootloader supported here). Both installing using Clover UEFI and Clover legacy are...

www.tonymacx86.com