Contribute
Register

Mojave Intel HD 530

Status
Not open for further replies.
With new version 1.2.7 of WEG, this ig-platform-id 0x193B0005 won't work anymore. If you will update your WEG with the new version before the restart, changes your ig-platform-id with the recommended one which is 0x19120000. Otherwise, you can't boot your computer.
 
You can ditch the IntelGraphicsFixup.kext. I am running Mojave via GA-H170N-WIFI and Intel 3.70 GHz Core i3-6100 with Intel® HD Graphics 530 via DVI connector. Attached are my clover settings. Additionally, I've installed the following KEXTs:

AirportBrcmFixup.kext
AppleALC.kext
BT4LEContiunityFixup.kext
FakeSMC_ACPISensors.kext
FakeSMC_CPUSensors.kext
FakeSMC_GPUSensors.kext
FakeSMC_LPCSensors.kext
FakeSMC.kext
HibernationFixup.kext
IntelMausiEthernet.kext v2.4.0
Lilu.kext v.1.2.7
USBInjectAll.kext v0.6.7
WhateverGreen.kext v.1.2.3

I'm trying to get a hd530 fully working on a desktop Dell 3040 SFF with i5 6500 under 10.14.4.
in fact it works via Hdmi only in FHD with 7mb shown and some artefacts and minor lags...
Where did you get the patch "AppleIntelSKLGraphicsFrameBuffer" ? did you manualy enter the values ?
is it fully working for you (multi res, QE/CI etc ...) 4k ?
thanks.
 
HD530 was working for me on 10.14.3, but booting hangs after 10.14.4 update. If connecting monitor to NVIDIA GTX1060 card, I can boot up fine but with only 7MB IGX.

Using igfx 19128086 ig 19120000 injection true. Latest WEG and Lilu.

Did anyone run into the same issue?
 
Last edited:
trying to get HD530 to work as dual display. Currently have Saphirre RX580 . Enabled Internal graphics set up as screen shots. Will start to boot with HD5390 as prinmary graphics. It will start to boot Apple logo and progress bar run and then its flashes and goes black screen but continues to boot. When I switch on other monitor connected to RX580 all is good. It shows both graphics in Sys info . Screenshots are my current config. Running 10.14.4. How can I fix black screen? Do I need to patch framebuffer? Using latest lilu and WEG


Update: Finally got it running dual monitors. HD530 only has 1536MB memory but both monitors function

Set ig 0x193B0005 and inject intel, Lilu and WEG. Have to boot into whatever monitor is set to primary
Screen Shot 2019-04-04 at 12.02.36 PM.png
 

Attachments

  • Screen Shot 2019-04-04 at 12.22.27 AM.png
    Screen Shot 2019-04-04 at 12.22.27 AM.png
    504.6 KB · Views: 334
  • Screen Shot 2019-04-04 at 12.22.11 AM.png
    Screen Shot 2019-04-04 at 12.22.11 AM.png
    457.3 KB · Views: 360
  • Screen Shot 2019-04-03 at 11.41.22 PM.png
    Screen Shot 2019-04-03 at 11.41.22 PM.png
    1 MB · Views: 370
  • Screen Shot 2019-04-03 at 11.40.41 PM.png
    Screen Shot 2019-04-03 at 11.40.41 PM.png
    1.1 MB · Views: 367
  • Screen Shot 2019-04-04 at 12.02.36 PM.png
    Screen Shot 2019-04-04 at 12.02.36 PM.png
    573.3 KB · Views: 336
Last edited:
trying to get HD530 to work as dual display. Currently have Saphirre RX580 . Enabled Internal graphics set up as screen shots. Will start to boot with HD5390 as prinmary graphics. It will start to boot Apple logo and progress bar run and then its flashes and goes black screen but continues to boot. When I switch on other monitor connected to RX580 all is good. It shows both graphics in Sys info . Screenshots are my current config. Running 10.14.4. How can I fix black screen? Do I need to patch framebuffer? Using latest lilu and WEG


Update: Finally got it running dual monitors. HD530 only has 1536MB memory but both monitors function

Set ig 0x193B0005 and inject intel, Lilu and WEG. Have to boot into whatever monitor is set to primary
Screen Shot 2019-04-04 at 12.02.36 PM.png


When I was using dual monitors I had to plug one in first and wait for full boot to plug in the second. I am on a GA-Z170N-WIFI it has two HDMI ports.
 
I have the Elitedesk 800 G2 and I've quite successfully installed Mojave. Everything works except graphics. I only get 1024x768. I've read about some monitor problems, but I also have some artifacts in finder, so I guess it's the driver?
I've tried fakeID: 0x19160000, 0x19120000, 0x12345678, 0x19020000
I've checked: Intel inject
My steps are:
1. Boot inte Mojave
2. Start Clover configurator, mount EFI.
3. Open EFI -> EFI -> CLOVER -> config.plist with Clover configurator.
4. I try to experiment with some changes.
5. Save the file to same directory.
6. Shutdown and restart.

Am I doing something wrong in these steps?
Do I need to install Whatevergreen or lilu? Do I need to compile these?
Can I use kextbeast to install whatevergreen and lilu?

Thanks, Lars.
 
I have the Elitedesk 800 G2 and I've quite successfully installed Mojave. Everything works except graphics. I only get 1024x768. I've read about some monitor problems, but I also have some artifacts in finder, so I guess it's the driver?
I've tried fakeID: 0x19160000, 0x19120000, 0x12345678, 0x19020000
I've checked: Intel inject
My steps are:
1. Boot inte Mojave
2. Start Clover configurator, mount EFI.
3. Open EFI -> EFI -> CLOVER -> config.plist with Clover configurator.
4. I try to experiment with some changes.
5. Save the file to same directory.
6. Shutdown and restart.

Am I doing something wrong in these steps?
Do I need to install Whatevergreen or lilu? Do I need to compile these?
Can I use kextbeast to install whatevergreen and lilu?

Thanks, Lars.

Try the following for your listed Intel HD 4400 graphics in Profile
  1. Boot into Mojave
  2. Start Clover configurator, mount EFI of System Disk
  3. Open EFI -> EFI -> CLOVER -> config.plist with Clover configurator.
  4. Go to the top half of Left Panel [SECTIONS]
  5. Scroll down to Devices >FakeID > IntelGFX and type in 0x04128086
  6. Scroll down to Graphics> [√]InjectIntel .........>>>>>>> [Ig-platform-id] and type in 0x0D220003
  7. Scroll down to bottom Left panel and locate the 2nd short arrow > Click Save As.. config.plist>OK
 
guido79:
I have the same problem as you. Did you solve the 1024x768 problem?
 
Status
Not open for further replies.
Back
Top