- Joined
- Mar 17, 2016
- Messages
- 19
- Motherboard
- Gigabyte Z97M-D3H
- CPU
- i5 4670K
- Graphics
- MSI GT710 2GB
- Mac
- Mobile Phone
System:
Motherboard: z97m-d3h
CPU: 4670K
GPU: Inbuilt HD4600
SMBios: iMac 14,2
The first time i ran Multibeast post installation, I could see HD4600, 1543MB in 'About this Mac' section. Later i messed up with some settings and had to do a fresh install.
In my 2nd and 3rd installation attempt, i am unable to get full QE/CI inspite of following the exact same procedures with Multibeast.
My VendorIDeviceID (8086:0412) is natively supported in IntelAppleHD5000.kext.
and furthermore in terminal bdmesg I get this:
---------------------------------------------
------------ INTEL DEVICE INFO --------------
---------------------------------------------
Class code: [0300]
Intel HD Graphics 4600 [8086:0412] (rev 06)
Subsystem: [1458:d000] :: PciRoot(0x1)/Pci(0x2,0x0)
Using default ig-platform-id of 0d220003
---------------------------------------------
I am perplexed so as to why the kext's are not loading even after using proper boot flags / org.chameleon.boot.plist.
I was thinking I was going to have to add a IGPlatformID flag to my chameleon plist but these show without a doubt that the CPU and hd 4600 graphics are being recognized. It's just being allotted 3MB when it should be getting the 64MB that my BIOS settings are set to. All I can land on for a problem is the No Kext Loaded in Kernel Extension Info.
Boot Flags: -v PCIRootUID=1 IGPEnabler=Yes GraphicsEnabler=No
Additional Flags Tried: 'Graphics Mode'=1600x1200x32 IGPlatformID=0d220003 IGPDeviceID=0412
Note: i've removed all kext with AppleIntelHD3000*, AppleIntelHD4000*, AppleIntelHDSNB* from S/L/E.
How do i resolve this issue?
Motherboard: z97m-d3h
CPU: 4670K
GPU: Inbuilt HD4600
SMBios: iMac 14,2
The first time i ran Multibeast post installation, I could see HD4600, 1543MB in 'About this Mac' section. Later i messed up with some settings and had to do a fresh install.
In my 2nd and 3rd installation attempt, i am unable to get full QE/CI inspite of following the exact same procedures with Multibeast.
My VendorIDeviceID (8086:0412) is natively supported in IntelAppleHD5000.kext.
and furthermore in terminal bdmesg I get this:
---------------------------------------------
------------ INTEL DEVICE INFO --------------
---------------------------------------------
Class code: [0300]
Intel HD Graphics 4600 [8086:0412] (rev 06)
Subsystem: [1458:d000] :: PciRoot(0x1)/Pci(0x2,0x0)
Using default ig-platform-id of 0d220003
---------------------------------------------
I am perplexed so as to why the kext's are not loading even after using proper boot flags / org.chameleon.boot.plist.
I was thinking I was going to have to add a IGPlatformID flag to my chameleon plist but these show without a doubt that the CPU and hd 4600 graphics are being recognized. It's just being allotted 3MB when it should be getting the 64MB that my BIOS settings are set to. All I can land on for a problem is the No Kext Loaded in Kernel Extension Info.
Boot Flags: -v PCIRootUID=1 IGPEnabler=Yes GraphicsEnabler=No
Additional Flags Tried: 'Graphics Mode'=1600x1200x32 IGPlatformID=0d220003 IGPDeviceID=0412
Note: i've removed all kext with AppleIntelHD3000*, AppleIntelHD4000*, AppleIntelHDSNB* from S/L/E.
How do i resolve this issue?