Intel uhd 630 hdmi, dvi no display, only vga works

[Maruth]

Greetings!!
CPU:Intel i7 8700
MOBO: Gigabyte B360M DS3H
RAM:32 GB
graphics : intel uhd 630
OS: High Sierra 10.13.5

Everything is working fine except:
1) HDMI and DVI ports do not display with hardware acceleration.only vga monitor has display. If the hardware acceleration is removed then HDMI and DVI work.
Igfx id is set to 0x5912000
Device ID 0x59128608
CPU : Mac 17,1
with AAPL,GfxYTile set to 0AAAAA00 DATA for the hardware acceleration to work.
Please advise

 

[sergio140]

Hi, could you tell me the BIOS options do you use? I tried with VT-d disabled, Fast boot disabled, XHCI Hand-off Enabled... and can't reach the installation page.

Thanks in advance.

 

[Spagnoletto]

Do you find an answer ? I have only vga too...

 

[xwpd]

Me too, if you find a way, let me know.

 

[nofirgus]

CPU:Intel i5 8500
MOBO: Gigabyte B360M DS3H
RAM:16 GB
graphics : intel uhd 630
OS: Mojave 10.14.1

I have the same situation, only VGA connector work, others "no signal" after boot. (Very strange, but that VGA supported hot plug)
I tried many combinations:

• boot with one VGA/DVI/HDMI display and plug other VGA/DVI/HDMI
• with and without Whatevergreen
• set ig-platform-id and intelGFX
• set AAPL,ig-platform-id
• without ig-platform-id at all (our Vcard supported natively)
• different SMBIOS: iMac18,[1,2,3], Macmini8,1 and even MacPro
• Also I tried change type of ports with Whatevergreen

But no way

PS1: Also I noticed that Intel FB-Patcher app cannot detect framebuffer for UHD630
PS2: In HS 10.13.5 I could boot with one DVI and after boot connect other HDMI display (I can upload config)

 

[poles]

CPU:Intel i5 8500
MOBO: Gigabyte B360M DS3H
RAM:16 GB
graphics : intel uhd 630
OS: Mojave 10.14.1

I have the same situation, only VGA connector work, others "no signal" after boot. (Very strange, but that VGA supported hot plug)
I tried many combinations:

• boot with one VGA/DVI/HDMI display and plug other VGA/DVI/HDMI
• with and without Whatevergreen
• set ig-platform-id and intelGFX
• set AAPL,ig-platform-id
• without ig-platform-id at all (our Vcard supported natively)
• different SMBIOS: iMac18,[1,2,3], Macmini8,1 and even MacPro
• Also I tried change type of ports with Whatevergreen

But no way

PS1: Also I noticed that Intel FB-Patcher app cannot detect framebuffer for UHD630
PS2: In HS 10.13.5 I could boot with one DVI and after boot connect other HDMI display (I can upload config)

You are right. The Intel FB Patcher can't detect framebuffer for UHD630. Maybe @headkaze can tell whats wrong. Also did you get full accelaration using VGA?

 

[nofirgus]

You are right. The Intel FB Patcher can't detect framebuffer for UHD630. Maybe @headkaze can tell whats wrong. Also did you get full accelaration using VGA?

I was wrong, for correct display all framebuffers you just need choice OS version in top menu FB Patcher APP
I got full acceleration using VGA, also I got HDMI with replug connector after boot OS
I attached my efi folder if anybody need

UPD: In my config.plist the section smbios with wrong SN and some other related keys, they are needed to be replaced by correct value

 

[poles]

I did that but for i3 8100 its not being detected

Fbpatcher1.6.6-on-i3-8100

• poles
• Dec 17, 2018

 

[nofirgus]

How do you inject your ig-platform-id? And what value you set?
Seems you need set 0x3E9B0007

<key>AAPL,ig-platform-id</key>
<data>BwCbPg==</data>

 

[attend]

I have used Lilu+whatevergreen, and dp & cdmi are ok. here is my config which I have copied from a post here.