Contribute
Register

Intel Network adapters on OS X: Small Tree drivers

Joined
Oct 19, 2018
Messages
1
Motherboard
Supermicro X8DTi
CPU
2x E5506
Graphics
GTX 1060
Hello! Please tell me how to make the adapter work 82576 Gigabit ET Dual Port.
https://pci-ids.ucw.cz/read/PC/8086/10c9
There is no PCI card in the system information. In the "Network" section there are two adapters:
Ethernet (en0):
Type: Ethernet
Hardware: Ethernet
BSD Device Name: en0
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
Ethernet:
MAC address: 00: 25: 90: 1d: 18: 86
Media Parameters:
Media Sub Type: Auto Select
Proxy:
Exceptions List: * .local, 169.254 / 16
Passive FTP mode: Yes
Service order: 2

Ethernet (en1):
Type: Ethernet
Hardware: Ethernet
BSD Device Name: en1
IPv4:
Configuration Method: DHCP
IPv6:
Configuration Method: Automatic
Ethernet:
MAC address: 00: 25: 90: 1d: 18: 87
Media Parameters:
Media Sub Type: Auto Select
Proxy:
Exceptions List: * .local, 169.254 / 16
Passive FTP mode: Yes
Service order: 1
In the network settings, they also exist, but they do not work, the link does not rise.

PS/ I apologize for the English language.
 
Joined
Jan 28, 2010
Messages
232
Motherboard
ASUS X99-E WS
CPU
E5-2697 V3
Graphics
GTX 760
Yes it worked for me with the Sage/10G and the X550-AT2 onboard. Unfortunately I returned the board until I can sell my original Sage and Rampage VI Extreme boards. Seemed to be much more reliable than installing in /L/E

This method works for me too on the Sage 10G, but why not just flash with ethtools? Then you don't ever have to worry about kext loading order issues again. Flashing is the true solution here, not juggling fakepciid loading order around.
 
Joined
Apr 18, 2011
Messages
1,329
Motherboard
ASUS ROG Z690 Extreme
CPU
Intel i9-12900k
Graphics
Radeon Pro W5500
Mac
  1. MacBook Air
  2. Mac Pro
Mobile Phone
  1. iOS
This method works for me too on the Sage 10G, but why not just flash with ethtools? Then you don't ever have to worry about kext loading order issues again. Flashing is the true solution here, not juggling fakepciid loading order around.

I didn’t have the board long enough to mess with flashing. Have you tried flashing?
 
Joined
Jan 28, 2010
Messages
232
Motherboard
ASUS X99-E WS
CPU
E5-2697 V3
Graphics
GTX 760
I didn’t have the board long enough to mess with flashing. Have you tried flashing?

Yep, flashing works fine. Same method as any other Intel card in this thread. Flash, then install the driver (it installs to L/E) and it just works!
 

anonym323

Banned
Joined
Nov 9, 2012
Messages
99
Motherboard
Asus X299 Deluxe
CPU
i9-7980XE
Graphics
Vega 64
Mac
  1. MacBook Pro
  2. Mac Pro
Mobile Phone
  1. iOS
Ups... Edited the wrong part first...
Now up and running fine :)
 
Last edited:
Joined
Jul 20, 2014
Messages
857
Motherboard
AsRock X299 Creator
CPU
i9-10900X
Graphics
RX 6800 XT
Mac
  1. MacBook Pro
Mobile Phone
  1. iOS
Hello
I've just get an X299 Sage 10G with X550-T2
I tried @slawa post #266 without success
Is there anyone with the same motherboard with the 10G ports fully functioning ?

I've tried to flash (fail again !! )
diviceID.png the Vendor/Device-ID is 1043,8712
epn225s0.pngIntel X550-T2 is assigned to enp225s0f0 & enp225s0f1
offset0x0240.png "sudo ethtool -e enp225s0 | less" I find the offset 0x0240
ethtool-error.png "sudo ethtool -E enp225s0f0 magic 0x15288086 offset 0x242 value 0x0a" give me an error : "Cannot set EEPROM data: Invalid argument"
I certainly did something wrong !! Any advice ?
Thanks in advance
 
Joined
May 27, 2016
Messages
84
Motherboard
Asus x99 Delux II
CPU
i7 6950
Graphics
Radeon VII
Mac
  1. iMac
Classic Mac
  1. PowerBook
magic should be 0x15638086 for you.

Hello
I've just get an X299 Sage 10G with X550-T2
I tried @slawa post #266 without success
Is there anyone with the same motherboard with the 10G ports fully functioning ?

I've tried to flash (fail again !! )
View attachment 369818 the Vendor/Device-ID is 1043,8712
View attachment 369819Intel X550-T2 is assigned to enp225s0f0 & enp225s0f1
View attachment 369820 "sudo ethtool -e enp225s0 | less" I find the offset 0x0240
View attachment 369821 "sudo ethtool -E enp225s0f0 magic 0x15288086 offset 0x242 value 0x0a" give me an error : "Cannot set EEPROM data: Invalid argument"
I certainly did something wrong !! Any advice ?
Thanks in advance
 
Top