Contribute
Register

How can I create my own DSDT?

Joined
May 8, 2020
Messages
2
Motherboard
SuperMicro X11SSH-F
CPU
E3-1220
Classic Mac
128K, 512K, iMac, PowerBook, Quadra
Mobile Phone
iOS, Other
I have installed Ubuntu 18.04 on a SuperMicro X11SSH-F motherboard, I would like to generate a DSDT based on this motherboard, if possible. I already tried using `iasl -T DSDT` however the output is

/*
* Intel ACPI Component Architecture
* iASL Compiler/Disassembler version 20180105 (64-bit version)
* Copyright (c) 2000 - 2018 Intel Corporation
*
* Template for [DSDT] ACPI Table (AML byte code table)
*/
DefinitionBlock ("", "DSDT", 2, "Intel", "_DSDT_01", 0x00000001)
{
Method (DS01)
{
}
}


And it looks unbelievably short.

Further here is a list of the PCI devices

$ lspci -vvv
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers (rev 05)
Subsystem: Super Micro Computer Inc Device 0884
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: ie31200_edac
Kernel modules: ie31200_edac

00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor PCIe Controller (x16) (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 25
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: df100000-df3fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:13.0 Non-VGA unclassified device: Intel Corporation 100 Series/C230 Series Chipset Family Integrated Sensor Hub (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H Integrated Sensor Hub
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 20
Region 0: Memory at df722000 (64-bit, non-prefetchable) [size=4K]

Capabilities: <access denied>
Kernel modules: intel_ish_ipc

00:14.0 USB controller: Intel Corporation 100 Series/C230 Series Chipset Family USB 3.0 xHCI Controller (rev 31) (prog-if 30 [XHCI])
Subsystem: Super Micro Computer Inc Sunrise Point-H USB 3.0 xHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at df700000 (64-bit, non-prefetchable) [size=64K]

Capabilities: <access denied>
Kernel driver in use: xhci_hcd

00:14.2 Signal processing controller: Intel Corporation 100 Series/C230 Series Chipset Family Thermal Subsystem (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H Thermal subsystem
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at df721000 (64-bit, non-prefetchable) [size=4K]

Capabilities: <access denied>
Kernel driver in use: intel_pch_thermal
Kernel modules: intel_pch_thermal

00:16.0 Communication controller: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #1 (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H CSME HECI
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df720000 (64-bit, non-prefetchable) [size=4K]

Capabilities: <access denied>
Kernel modules: mei_me

00:16.1 Communication controller: Intel Corporation 100 Series/C230 Series Chipset Family MEI Controller #2 (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H CSME HECI
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df71f000 (64-bit, non-prefetchable) [size=4K]

Capabilities: <access denied>
Kernel modules: mei_me

00:17.0 SATA controller: Intel Corporation Q170/Q150/B150/H170/H110/Z170/CM236 Chipset SATA Controller [AHCI Mode] (rev 31) (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Sunrise Point-H SATA controller [AHCI mode]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 35
Region 0: Memory at df710000 (32-bit, non-prefetchable) [size=8K]

Region 1: Memory at df71e000 (32-bit, non-prefetchable)
Region 2: I/O ports at f050
Region 3: I/O ports at f040
Region 4: I/O ports at f020
Region 5: Memory at df71d000 (32-bit, non-prefetchable) [size=2K]

Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

00:1c.0 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #1 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 26
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: df600000-df6fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #2 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: df500000-df5fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.4 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #5 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 28
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: df400000-df4fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.6 PCI bridge: Intel Corporation 100 Series/C230 Series Chipset Family PCI Express Root Port #7 (rev f1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 29
Bus: primary=00, secondary=05, subordinate=06, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: de000000-df0fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1f.0 ISA bridge: Intel Corporation C236 Chipset LPC/eSPI Controller (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H LPC Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:1f.2 Memory controller: Intel Corporation 100 Series/C230 Series Chipset Family Power Management Controller (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H PMC
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at df718000 (32-bit, non-prefetchable) [disabled] [size=16K]


00:1f.4 SMBus: Intel Corporation 100 Series/C230 Series Chipset Family SMBus (rev 31)
Subsystem: Super Micro Computer Inc Sunrise Point-H SMBus
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df71c000 (64-bit, non-prefetchable)
Region 4: I/O ports at f000
Kernel modules: i2c_i801

01:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS-3 3008 [Fury] (rev 02)
Subsystem: LSI Logic / Symbios Logic MegaRAID SAS-3 3008 [Fury]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e000
Region 1: Memory at df300000 (64-bit, non-prefetchable) [size=64K]

Region 3: Memory at df200000 (64-bit, non-prefetchable) [size=1M]
Expansion ROM at df100000 [disabled] [size=1M]
Capabilities: <access denied>
Kernel modules: megaraid_sas

02:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
Subsystem: Super Micro Computer Inc I210 Gigabit Network Connection
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df600000 (32-bit, non-prefetchable) [size=512K]

Region 2: I/O ports at d000
Region 3: Memory at df680000 (32-bit, non-prefetchable) [size=16K]

Capabilities: <access denied>
Kernel driver in use: igb
Kernel modules: igb

03:00.0 Ethernet controller: Intel Corporation I210 Gigabit Network Connection (rev 03)
Subsystem: Super Micro Computer Inc I210 Gigabit Network Connection
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at df500000 (32-bit, non-prefetchable) [size=512K]

Region 2: I/O ports at c000
Region 3: Memory at df580000 (32-bit, non-prefetchable) [size=16K]

Capabilities: <access denied>
Kernel driver in use: igb
Kernel modules: igb

04:00.0 Non-Volatile memory controller: Device 1cc1:8201 (rev 03) (prog-if 02 [NVM Express])
Subsystem: Device 1cc1:8201
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
NUMA node: 0
Region 0: Memory at df400000 (64-bit, non-prefetchable) [size=16K]

Capabilities: <access denied>
Kernel driver in use: nvme
Kernel modules: nvme

05:00.0 PCI bridge: ASPEED Technology, Inc. AST1150 PCI-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=05, secondary=06, subordinate=06, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: de000000-df0fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp

06:00.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (rev 30) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc ASPEED Graphics Family
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]

Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at b000
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]

Capabilities: <access denied>
Kernel driver in use: ast
Kernel modules: ast


Are there any other pieces of information that can help determine if it's possible to run Catalina on this machine?

$ inxi -v7
System: Host: smws01 Kernel: 4.15.0-99-generic x86_64 bits: 64 gcc: 7.5.0 Console: tty 0
Distro: Ubuntu 18.04.4 LTS
Machine: Device: server System: Supermicro product: Super Server v: 0123456789 serial: N/A
Mobo: Supermicro model: X11SSH-F v: 1.01 serial: N/A
UEFI: American Megatrends v: 2.0b date: 07/27/2017
Chassis: type: 17 v: 0123456789 serial: N/A
CPU: Quad core Intel Xeon E3-1220 v6 (-MT-MCP-) arch: Skylake rev.9 cache: 8192 KB
flags: (lm nx sse sse2 sse3 sse4_1 sse4_2 ssse3 vmx) bmips: 24000
clock speeds: min/max: 800/3500 MHz 1: 800 MHz 2: 800 MHz 3: 800 MHz 4: 800 MHz
Memory: Using dmidecode: root required for dmidecode
Graphics: Card: ASPEED ASPEED Graphics Family bus-ID: 06:00.0 chip-ID: 1a03:2000
Display Server: N/A driver: ast tty size: 251x75 Advanced Data: N/A out of X
Network: Card-1: Intel I210 Gigabit Network Connection
driver: igb v: 5.4.0-k port: d000 bus-ID: 02:00.0 chip-ID: 8086:1533
IF: eno1 state: down mac: ac:1f:6b:1a:04:b8
Card-2: Intel I210 Gigabit Network Connection
driver: igb v: 5.4.0-k port: c000 bus-ID: 03:00.0 chip-ID: 8086:1533
IF: eno2 state: up speed: 1000 Mbps duplex: full mac: ac:1f:6b:1a:04:b9
WAN IP: 93.83.73.255
IF: eno1 ip-v4: N/A ip-v6-link: N/A
IF: docker0 ip-v4: 172.17.0.1 ip-v6-link: N/A
IF: eno2 ip-v4: 10.77.99.54 ip-v6-link: fe80::ae1f:6bff:fe1a:4b9
Drives: HDD Total Size: 512.1GB (1.4% used)
ID-1: /dev/nvme0n1 model: ADATA_SX8200PNP size: 512.1GB serial: 2K1120097360 firmware: 42A4SANA
Optical: No optical drives detected.
Partition: ID-1: / size: 468G used: 6.8G (2%) fs: ext4 dev: /dev/nvme0n1p2
label: N/A uuid: b78190ee-0c22-4cef-bd63-13e7c571ce79
ID-2: /boot/efi size: 511M used: 6.1M (2%) fs: vfat dev: /dev/nvme0n1p1 label: N/A uuid: 75C7-FEB2
RAID: System: supported: linear multipath raid0 raid1 raid6 raid5 raid4 raid10
No RAID devices: /proc/mdstat, md_mod kernel module present
Unused Devices: none
Unmounted: ID-1: /dev/nvme0n1 size: 512.11G label: N/A uuid: N/A
Sensors: System Temperatures: cpu: 29.8C mobo: 21.5C
Fan Speeds (in rpm): cpu: N/A
Info: Processes: 166 Uptime: 2:08 Memory: 860.9/7923.7MB Init: systemd v: 237 runlevel: 5 Gcc sys: 7.5.0
Client: Shell (bash 4.4.201 running in tty 0) inxi: 2.3.56
 
Last edited:

jaymonkey

Moderator
Joined
Aug 27, 2011
Messages
3,817
Motherboard
ASRock-Z97 EX6
CPU
i7-4790K OC @ 4.8GHz
Graphics
Vega 64LC + HD4600
Mac
MacBook Air, MacBook Pro
Mobile Phone
Android, iOS
@ggt667,

There is no need to use Linux to dump the ACPI tables.

Just press F4 while in Clover which will dump both the DSDT and all the SSDT tables.
You'll find the output in the following folder :-

Code:
/EFI/Clover/ACPI/origin

The process is detailed in the following guide :-


Although written for laptops most of the guid is also relevant for desktops.

That said it is usually not necessary to manually patch the DSDT on desktops, we usually hot patch it using Clover ACPI fixes and custom SSDT's.

Cheers
Jay
 
Joined
May 8, 2020
Messages
2
Motherboard
SuperMicro X11SSH-F
CPU
E3-1220
Classic Mac
128K, 512K, iMac, PowerBook, Quadra
Mobile Phone
iOS, Other
How long does it take to make a USB w/UniBeast? I'm running this on my iMac 2013 w/32 GB RAM and 512GB Flash Storage.

This is what I'm looking at at 15 hours into the process
1589017427629.png


I see no option to see what UniBeast is up to.
 
Last edited:
Top