- Joined
- May 1, 2015
- Messages
- 7
- Motherboard
- Dq35mp
- CPU
- E8300
- Graphics
- HD 7850
- Mac
- Classic Mac
- Mobile Phone
Hi Guys, I'm new btw
So I'm a complete noob when it comes to hackintoshes. I recently installed Yosemite via Unkbeast and Multibeast as per the install guide several times but can't get the system to reboot after installing Multibeast. Originally I had the boot0: done and gibberish error but I managed to fix it by replacing two Kexts (AMDcontroller7000.kext and amdradeonaccelorator.kext) as well as moving my boot loader to the EFI partition but now I can't boot as I get the following Kernel panic seen in the pictures.
in safe mode (-x) I get this
https://www.dropbox.com/s/z8x5nsjrtvr2h8l/photo 29-04-2015 08 01 36.jpg?dl=0
In verbose (-v) I get this
https://www.dropbox.com/s/ly7d3xz65gg5at9/photo 01-05-2015 21 06 25.jpg?dl=0
i have tried all the possible bootflags: GraphicsEnabler=No maxmem=4096 -v -x -f -F PCIRootUID=1 Acpi=Off
Now because the dependency says ACPI I'm leaning towards the fact that it is the problem. Perhaps it is an incorrect BIOS setting. Can somebody tell me what settings I should use here on my BIOS, I've tried most of them.
https://www.dropbox.com/s/63aqspym2yuxh68/photo 01-05-2015 21 37 55.jpg?dl=0
Also under HPET in my Bios I've only got the option of of Enabled or Disbaled as opposed to 64. Is that a problem, although usually the default is 64 on newer motherboards.
Here is my hardware:
Intel Core 2 Dup e8300
Intel DQ35mp motheroard
AMD HD 7850
4GB DDR2
All your help would be much appreciated.
So I'm a complete noob when it comes to hackintoshes. I recently installed Yosemite via Unkbeast and Multibeast as per the install guide several times but can't get the system to reboot after installing Multibeast. Originally I had the boot0: done and gibberish error but I managed to fix it by replacing two Kexts (AMDcontroller7000.kext and amdradeonaccelorator.kext) as well as moving my boot loader to the EFI partition but now I can't boot as I get the following Kernel panic seen in the pictures.
in safe mode (-x) I get this
https://www.dropbox.com/s/z8x5nsjrtvr2h8l/photo 29-04-2015 08 01 36.jpg?dl=0
In verbose (-v) I get this
https://www.dropbox.com/s/ly7d3xz65gg5at9/photo 01-05-2015 21 06 25.jpg?dl=0
i have tried all the possible bootflags: GraphicsEnabler=No maxmem=4096 -v -x -f -F PCIRootUID=1 Acpi=Off
Now because the dependency says ACPI I'm leaning towards the fact that it is the problem. Perhaps it is an incorrect BIOS setting. Can somebody tell me what settings I should use here on my BIOS, I've tried most of them.
https://www.dropbox.com/s/63aqspym2yuxh68/photo 01-05-2015 21 37 55.jpg?dl=0
Also under HPET in my Bios I've only got the option of of Enabled or Disbaled as opposed to 64. Is that a problem, although usually the default is 64 on newer motherboards.
Here is my hardware:
Intel Core 2 Dup e8300
Intel DQ35mp motheroard
AMD HD 7850
4GB DDR2
All your help would be much appreciated.