Contribute
Register

[GUIDE] [Skylake] El Capitan MSI Z170A-Tomahawk + i5 6600K + GTX 970

Status
Not open for further replies.
Joined
Jul 22, 2015
Messages
18
Motherboard
ASUS Prime Z270AR
CPU
Intel Core i7-7700K (Kabylake)
Graphics
Nvidia GeForce GTX 970
Mobile Phone
  1. Android
El Capitan 10.11.3 On
MSI Z170A-Tomahawk, i5 6600K, GTX970, 16 GB DDR4,
U
nibeast & Multibeast

Prerequisites:
8GB or More Unibeast USB - Follow Steps 1 & 2 from Here
2GB or More USB for Downloaded Utilities & Prerequisite files!
Blank HDD (To Install Hackintosh onto)
Patience


Utilities:
Unibeast 6.1.1

Multibeast 8.1.1
EFIMounter v3
Kext Wizard
AGDPfix (Fixes Black Screen when using iMac 17,1 SMBIOS) CREDITS AND THANKS TO shilohh!!


Files, Drivers and kexts
OsxAptioFixDrv-64.efi
OsxAptioFix2Drv-64.efi
Preconfigured Skylake config.plist
USBInjectAll.kext
Nvidia Web Drivers
After Install config.plist
ALC892 Kexts

Whats Working & Whats Not?
Everything is working 100% except for Most USB 3.1 Ports except for 1. Audio works now works 100% with no Static noise.

Note
To make it easier if you have Windows also installed i recommend saving the settings you want for booting Windows as an overclock profile & same for mac. Name one Windows & the other Hackintosh etc. Every time when you load or change the profile you will need to change the boot device to whatever HDD with the OS your trying to boot.

Pre Install Setup And Configuration
0) Copy all downloaded files to a spare USB
1) Follow Steps 1 & 2 from this Link (Thanks to tonymacx86)
You should now have a working El Capitan USB Installer
2) In finder you should now find a mounted drive called EFI. If not Run EfiMounter v3 and click mount and choose the corresponding drive.
3) Navigate into /EFI/CLOVER/drivers64UEFI/
4) Delete
OsxAptioFix2Drv-64.efi & Copy OsxAptioFixDrv-64.efi to /EFI/Clover/drivers64UEFI
5) Go Back a folder and delete config.plist and replace with the preconfigured config.plist
6) Open Kexts folder and all numbered folders before 10.10 (10.9, 10.8, 10.7 etc)
7) Copy over USBInjectAll.Kext into the 10.10 & 10.11 folder

DO NOT DELETE THE FILES. COPY THEM TO A SPARE USB AS YOU WILL NEED THEM LATER!!

BIOS Configuration
LAN Option ROM - Disabled
Network Stack - Disabled
Serial(COM) Port 0 - Disabled
Parallel(LPT) Port - Disabled
Windows 8.1/10 WHQL- Disabled
Windows 7 Installation - Disabled
Intel Virtualization - Disabled
Intel VT-D - Disabled
CFG Lock - Disabled

Installation
1) Boot up the computer and enter the Boot selection menu by tapping F11 on the post screen
2) Select the USB Drive you created earlier with Unibeast
3) Navigate to Options using your keyboard & add nv_disable=1 to the boot args section and press enter
4) Navigate back to the selection menu by pressing ESC on your keyboard and select the hackintosh USB
5) Once in the El Capitan install screen make sure to format the HDD you will be using to install El Capitan on by going up the top of the screen and selecting Utilities then Disk Utility. Make sure to select the correct HDD. Give the hdd a name of your choosing
6) Once install finishes and reboots boot the USB again & add the boot arguments again and boot from the formatted drive you renamed earlier in Clover
7) Run through the initial configuration screen and create your User
8) Once on the desktop plug the USB into any USB 2.0 port (Front or back) and copy all the downloaded files you copied earlier to the desktop.
9) Run extract Multibeast and run it.
10) Select
Quickstart - UEFI Boot Mode
Drivers > Audio > Realtek ALCxxx - ALC892
Drivers > Misc - Leave Default
Customise > System Definitions - Mac Pro 3.1
Make sure the HDD is selected not the USB & click
Build > Install
11) Run EFIMounter v3 & select the HDD not the USB.
12) Once mounted
navigate into /EFI/CLOVER/ and delete config.plist and replace with the downloaded one
13)
Open Kexts folder and all numbered folders before 10.10 (10.9, 10.8, 10.7 etc)
14)
Copy over USBInjectAll.Kext into the 10.10 & 10.11 folder
15)
Remove the USB drive and Reboot, add the boot arguments from before and boot from the Hackintosh HDD you renamed earlier
16) Once rebooted install the Nvidia Web Drivers (DO NOT PRESS THE RESTART BUTTON YET)
17) Mount the HDD using EFIMounter v3 and navigate to
/EFI/CLOVER/ and delete config.plist
18) Copy the copyafter-config.plist to /EFI/CLOVER/ and rename to config.plist
19) Unzip
AGDPfix and run AGDPfix.app and press ok to everything.
20) Unzip ALC892 Kexts & Open Kext Wizard
21) Once in Kext Wizard tick the box for /System/Library/Extensions (Make sure Repair Permissions is not ticked)
22) Press the Installation tab and browse then navigate to where you extracted the ALC892 Kexts folder and select both files in that folder.
23) Once selected click install.
24) Once installed reboot and audio should now be working :)

Now you should be ready to reboot into a working Hackintosh System With working Audio
 

Attachments

  • config.plist
    5.4 KB · Views: 1,164
Thank you!

Finally ALC892 works.
 
Not a problem :)
 
Hey there! Just wondering if this is 6600K-specific? I'm sporting the exact same spec but with 6500 instead. Thanks!:think::think:
 
hello im try to but not boot my pc my spec, as it same but gtx 960 4gb not work
 

Attachments

  • mac.jpg
    mac.jpg
    5.5 KB · Views: 1,116
before installation my gtx 960 4gb
 

Attachments

  • mac.jpg
    mac.jpg
    5.5 KB · Views: 534
I don't think it would be as it is still Skylake. Give it a try but it should work :)
 
Are you booting with nv_disable=1? If yes then try enter nv_disable=1 -x -v
 
Thanks! I'll give it a shot over the weekend then!
 
Did you update to 10.11.4?
 
Status
Not open for further replies.
Back
Top