[Guide] Lenovo Y50/Y70 (UHD or 1080p) using Clover UEFI

[RehabMan]

it seem my DSDT is flawed
my sound dosent work tried all the usual fixes (no cache repair restart) no help

i think the issue in my old DSDT

so i went and booted my OSX el capitan with the USB and run the commands to make DSDT and SSDT
but when ever i use the new DSDT i get the massage in the attached pic

also attached all info requested in first post

Yans-MBP:~ yan$ kextstat|grep -y acpiplat
13 2 0xffffff7f8300c000 0x66000 0x66000 com.apple.driver.AppleACPIPlatform (4.0) 295F7A91-2DF7-3FFE-9550-A0C1A6F9D575 <12 11 7 6 5 4 3 1>
Yans-MBP:~ yan$ kextstat|grep -y appleintelcpu
Yans-MBP:~ yan$

thanks,

attached pic with the error i get at boot with new DSDT
the broken DSDT (in EFI folder there my old DSDT)
Ioreg for any case
native patchmatic files as they were extracted
and the EFI FOLDER

Your config.plist is wrong. It is not the one from the repo.

 

[masterscarhead1]

it seem my DSDT is flawed
my sound dosent work tried all the usual fixes (no cache repair restart) no help

i think the issue in my old DSDT

so i went and booted my OSX el capitan with the USB and run the commands to make DSDT and SSDT
but when ever i use the new DSDT i get the massage in the attached pic

also attached all info requested in first post

Yans-MBP:~ yan$ kextstat|grep -y acpiplat
13 2 0xffffff7f8300c000 0x66000 0x66000 com.apple.driver.AppleACPIPlatform (4.0) 295F7A91-2DF7-3FFE-9550-A0C1A6F9D575 <12 11 7 6 5 4 3 1>
Yans-MBP:~ yan$ kextstat|grep -y appleintelcpu
Yans-MBP:~ yan$

thanks,

attached pic with the error i get at boot with new DSDT
the broken DSDT (in EFI folder there my old DSDT)
Ioreg for any case
native patchmatic files as they were extracted
and the EFI FOLDER

You're definitely doing something wrong. You have up to SSDT6, and the config.plist only has SSDT up to SSDT4 (and 9), so your SSDT5 and 6 aren't doing anything. Perhaps try doing the whole git pull, and ./download.sh ./install.sh stuff again. Also, did you remember to do make cleanallex if you're extracting from usb?

 

[RehabMan]

You're definitely doing something wrong. You have up to SSDT6, and the config.plist only has SSDT up to SSDT4 (and 9), so your SSDT5 and 6 aren't doing anything. Perhaps try doing the whole git pull, and ./download.sh ./install.sh stuff again. Also, did you remember to do make cleanallex if you're extracting from usb?

@shadowk155,

Just to add to what @mastercarhead1 says, suggestions:
- prepare USB per guide
- delete EFI/Clover from your EFI partition
- reinstall current Clover (as per guide)
- git pull (to get current repo)
- boot from USB
- make cleanallex
- follow the guide in post #1 for the rest (ACPI patching, ssdtPRgen.sh, config.plist, SMBIOS, etc)

 

[masterscarhead1]

@shadowk155,

Just to add to what @mastercarhead1 says, suggestions:
- prepare USB per guide
- delete EFI/Clover from your EFI partitioin
- reinstall current Clover (as per guide)
- git pull (to get current repo)
- boot from USB
- make cleanallex
- follow the guide in post #1 for the rest (ACPI patching, ssdtPRgen.sh, config.plist, SMBIOS, etc)

^ Also, look at your EFI/Clover/kexts. It's a mess in there, with all folders there, and kexts in multiple folders

 

[RehabMan]

^ Also, look at your EFI/Clover/kexts. It's a mess in there, with all folders there, and kexts in multiple folders

It will be no problem after this:

- delete EFI/Clover from your EFI partition
...
- follow the guide

 

[shadowk155]

It will be no problem after this:

i have followed the guide its just i started in hackintosh with manual tuning and it kinda hard giving up the wheel even if i have no idea what iam doing while holding it

well i managed to get it working with the new DSDT

your new PLIST remove several tags that used to be needed.

here is the ioreg can you see if everything where it suppose to be ?

thanks,

P.S. in the end i did an update and no clean install

 

[divinitus]

Thanks. I pulled your request.

I was experimenting on my desktop and didn't want to install files to its EFI....

No problem, happy to help

Anyway thanks for the 10.11 boot garble fix, was feeling a little icky once I upgraded but everything works perfectly now

 

[RehabMan]

i have followed the guide its just i started in hackintosh with manual tuning and it kinda hard giving up the wheel even if i have no idea what iam doing while holding it

If you're interested in what is going on, read the code in the scripts/makefile/etc.

your new PLIST remove several tags that used to be needed.

Nothing removed really, but some things added...

here is the ioreg can you see if everything where it suppose to be ?

Power management is not implemented. See post #1, "Power Management"

The rest looks as expected.

P.S. in the end i did an update and no clean install

That's fine and works if you start with a clean setup (eg. according to the guide).

 

[RehabMan]

No problem, happy to help

Anyway thanks for the 10.11 boot garble fix, was feeling a little icky once I upgraded but everything works perfectly now

Thanks... Enjoy.

 

[shadowk155]

Power management is not implemented. See post #1, "Power Management"
.

that odd i did do the power managment section but probbly did it wrong

i re did it

is it correct now ?

i did noticed a large size difference with the SSDT file (from the old one and the new one that i just made)