Contribute
Register

[Guide] Intel DH67xx with HD3000 using Clover UEFI hotpatch

Status
Not open for further replies.
Answering my own question - NO - I used the config from the beginning of this guide and made the changes to FakeID, platform-id, as you'd suggested to other Ivy-Bridge'ers in this thread. Also had to remove the "arbitrary HD3000" part to get it to work.

Currently booting properly from SSD and working in post-installation.
 
chickendinner said:
Thanks RehabMan - and I actually had one more question - since I am running a i5-3570k with this board would you recommend the "config_HD4000_1600x900_6series" from your laptop config repository for the install?
Click to expand...

You will need different changes for HD4000 on 6-series.
This guide is for HD3000 only.
It is discussed earlier in this thread.
 
hi, have the smae motherboard but with not with your onboard graphic
Code: 
lspci  -v -s  $(lspci | grep ' VGA ' | cut -d" " -f 1)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
    DeviceName: Intel(R) HD Graphics Device
    Subsystem: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller
    Flags: bus master, fast devsel, latency 0, IRQ 33
    Memory at fe000000 (64-bit, non-prefetchable) [size=4M]
    Memory at e0000000 (64-bit, prefetchable) [size=256M]
    I/O ports at f000 [size=64]
    [virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
    Capabilities: <access denied>
    Kernel driver in use: i915
    Kernel modules: i915
and with Intel® Core™ i3-2100T CPU @ 2.50GHz × 4
is that possible to install Sierra on it with your guide?

Regards
 
mamPHP said:
hi, have the smae motherboard but with not with your onboard graphic
Code: 
lspci  -v -s  $(lspci | grep ' VGA ' | cut -d" " -f 1)
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
    DeviceName: Intel(R) HD Graphics Device
    Subsystem: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller
    Flags: bus master, fast devsel, latency 0, IRQ 33
    Memory at fe000000 (64-bit, non-prefetchable) [size=4M]
    Memory at e0000000 (64-bit, prefetchable) [size=256M]
    I/O ports at f000 [size=64]
    [virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
    Capabilities: <access denied>
    Kernel driver in use: i915
    Kernel modules: i915
and with Intel® Core™ i3-2100T CPU @ 2.50GHz × 4
is that possible to install Sierra on it with your guide?

Regards
Click to expand...

Your CPU has HD2000. It is not supported.
You would need to add a compatible graphics card or different CPU with HD3000.
 
Ohh! i'm running now linux on it, everything work fine.My device is special created from HFX with passive cooler system (zero noise) no fan. Therefor can't touch it easily. I'll save money to buy some hardware just for hackintosh.


Thanks again :thumbup:
 
Hi again,
What's your recommendation for graphiccard, which can easily configure it with this cpu and hackintosh.
I have other pc for gaming. I need this hackintosh just for small videos editing and programming IDE.

Regards
 
Thanks, But i'm asking about a compatible GPU with my motherboard.
 
:-D
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top