JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser .
[Guide] HP Elite 8300 & 6300 Pro (all form factors) using Clover UEFI hotpatch
Status
Not open for further replies.
There are many problems with that config.plist you are using. Too many fixes and nothing in Devices -> Properties.
So this is quite peculiar. I simply replaced the semi-working config.plist (without audio) with the HD4000 config.plist as you recommended, but it is not booting now. Instead the system is hanging here:
Here are the two config.plists:
So this is quite peculiar. I simply replaced the semi-working config.plist (without audio) with the HD4000 config.plist as you recommended, but it is not booting now. Instead the system is hanging here:
I think it will require that you go back and start with a clean install and follow just this guide. Go through each of the steps and apply each one till you complete the whole thing. You need to have all the kexts and SSDTs in the right places for the HD4000 .plist to work. If I recall your PR files had nothing in the kexts/other folder and only one ssdt.aml in acpi/patched folder. Not going to get far with that scenario.
Last edited: Dec 4, 2019
I think it will require that you go back and start with a clean install and follow just this guide. Go through each of the steps and apply each one till you complete the whole thing. You need to have all the kexts and SSDTs in the right places for the HD4000 .plist to work. If I recall your PR files had nothing in the kexts/other folder and only one ssdt.aml in acpi/patched folder. Not going to get far with that scenario.
Hmmm... I followed the guide precisely
@trs96 . The only thing that was off was the Clover config.plist for some reason. I have verified that the files as noted are in the right places. The problem appears to be the RX580 card as that is the one that does not boot while the integrated video does with this HD4000 config.plist.
that is the one that does not boot while the integrated video does with this HD4000 config.plist.
Are you changing the BIOS setting to use the AMD graphics instead of leaving it set to Intel ? You must also disable legacy booting (legacy oproms) for the AMD card to work. Also make sure 8 pin power is connected to the RX 580 or it won't work.
@Sniki could you please post `find` results for /Library/Extensions & /Volumes/EFI? Ie:
$ find /Library/Extensions
$ find /Volumes/EFI # while EFI of course is mounted
FYI,
@yllapilate here are my results
/Library/Extensions
Spoiler
ACS6x.kext
EFI
Spoiler
/Volumes/EFI
Last edited: Dec 9, 2019
Just completed a simple update (10.15 to 10.15.2) after checking the latest backup. No updates to kexts or Clover. All good so far, lots of rebooting/soft reboots though, probably half a dozen.
Screen Shot 2019-12-18 at 12.15.23 am.png
128.9 KB
· Views: 81
Last edited: Dec 17, 2019
Just completed a simple update (10.15 to 10.15.2) after checking the latest backup. No updates to kexts or Clover. All good so far, lots of rebooting/soft reboots though, probably half a dozen.
Thank you
@Geezah , I was wondering if it wouldn't start without the latest undistributed kext.
Hi guys.
I have HP 6300 SFF, i5 3470, MSI ATI RX 550 LP 2GB and successfully installed Mojave 10.14.6 via local guide.
But I have some problems with booting time it increased by 1 minute !!! It happens after Inject ATI is on.
This is my losted 1 minute
2019-12-29 11:28:30.394988+0200 0x27d Default 0x0 0 0 kernel: (AppleRTC) RTC: getGMTTimeOfDay 1577611710
2019-12-29 11:29:29.043910+0200 0x74 Default 0x0 0 0 kernel: (IOGraphicsFamily) GTrace synchronization point 8
Please help me fix this problem. Debug attached.
debug_4935.zip
3.1 MB
· Views: 59
Last edited: Dec 29, 2019
2019-12-29 11:28:30.394988+0200 0x27d Default 0x0 0 0 kernel: (AppleRTC) RTC: getGMTTimeOfDay 1577611710
If the display is the start time, it takes time to synchronize the time.
Change SMBIOS to MacMini 6.1.
I don't know what "EmuVariableUefi.efi" is.
Status
Not open for further replies.
