[Guide] El Capitan on the Intel Skylake NUC

[johnnyx86]

hi,

ok this is what happened now. previously i have installed to the hard drive, since its slow i installed to my m.2 SSD then i formatted my hard disk now when i boot i got the clover boot screen but no icons to select to boot.

Attached is my clover folder.

 

[RehabMan]

hi,

ok this is what happened now. previously i have installed to the hard drive, since its slow i installed to my m.2 SSD then i formatted my hard disk now when i boot i got the clover boot screen but no icons to select to boot.

Attached is my clover folder.

I assume you are following my guide:
https://www.tonymacx86.com/threads/...g-clover-uefi-nuc6i5syk-nuc6i7kyk-etc.207848/
(you really should have posted there).

You forgot HFSPlus.efi in drivers64UEFI.
Read the guide carefully.

 

[AjfonAdam]

Hey,
Can you post a complete configuration (whole clover folder with all kexts). I have NUC6i5SYH, I installed hackintosh but I see that many of you have done this before and have the same computer.

Thank you for your help.

 

[RehabMan]

Hey,
Can you post a complete configuration (whole clover folder with all kexts). I have NUC6i5SYH, I installed hackintosh but I see that many of you have done this before and have the same computer.

Thank you for your help.

It is covered in the guide.
https://www.tonymacx86.com/threads/...g-clover-uefi-nuc6i5syk-nuc6i7kyk-etc.207848/

 

[DaveFK]

I followed the original post, however I am installing OSX Sierra onto my Nuc 615SYH. Booting and selecting HFS with my SSD will load about 3/4 of the way and get stuck at the apple menu. If I boot to the USB flash that I used for installation, then select my SSD the OS will load, am I missing something really easy here? I have followed the installation very closely.

Edit: BIOS update did not fix.

 

[phucknub]

I just installed the latest clover, and a reboot went fine, then installed the latest update (security & itunes), and now the system goes into a constant re-boot. Clover shows up fine, then when it boots, it resets the machine before the apple logo even shows up. Boot clover with verbose mode and not much more detail is shown, 2 lines. Something like :-
OsxAptioFixDrv: Starting overrides for System\Library\CoreServices\boot.efi
Using reloc block: yes, hibernate wake: no
xxxxxxxxxxxxxxxxxxxxxxxxxxxxx

Then reboots.

I've tried booting in recovery mode, but that doesn't seem to boot either, 1 hour later and it seems stuck.

Any ideas, I'm completely lost now?

Worst comes to the worst, is there a way to do some form of USB boot and save off the information on the hard drive before installing again?

 

[BreBo]

@phucknub, please update your profile (personal details) with your Motherboard or Make/Model, CPU and Graphics Card.

Profiles need to contain at least your primary system to assist others with helping you.

 

[phucknub]

@phucknub, please update your profile (personal details) with your Motherboard or Make/Model, CPU and Graphics Card.

Sorry, thought it was apparent from the thread.
Intel NUC 6i5-6260U 1.8GHz x 4
Intel Iris Graphics 540 (Skylake GT3e)

 

[BreBo]

Sorry, thought it was apparent from the thread.
Intel NUC 6i5-6260U 1.8GHz x 4
Intel Iris Graphics 540 (Skylake GT3e)

Great, now please update your profile (personal details) with your Motherboard or Make/Model, CPU and Graphics Card.

 

[Kaby123]

Is there a plan to update this guide in the near future to 10.12.6 on the Intel Kaby Lake NUC?

I realize that RehabMan has already done a good guide, https://www.tonymacx86.com/threads/...efi-nuc7i7bnh-nuc7i5bnk-nuc7i3bnh-etc.221123/

but i believe its a little too complicated for me,

Thanks