- Joined
- Mar 1, 2013
- Messages
- 943
- Motherboard
- GA-Z77X-UD5H
- CPU
- i7-3770K
- Graphics
- 2x GEFORCE GT 640
- Mac
- Mobile Phone
SPECS | Z77X-UD5H | i7-3770K | DUAL GT 640 | 16GB Memory | 250GB SSD
This install guide is for the GA-Z77X-UD5H. I built this CustoMac in Early 2013. I have been through every update since 10.8 as well as major software upgrades 10.9, 10.10 and now 10.11. I participated in the 10.11 Public Beta releases through the GM release. This board has served me very well and I have rarely experienced any issue with it. I am running a triple monitor setup with dual GPUs. At the time of writing this guide there are no guides specific to this board, so I though "Why not?"
For the installation of 10.11 I used a blank 250GB SSD and did a clean install of OS X 10.11 El Capitan. For the most part I followed the UniBeast 10.11 Install Guide, only differing during post install. For post install I used the latest stand alone version of Clover r3292. Before the installation, I removed one of the GT 640s from my system, this was reinstalled after everything was up and running. The install was very smooth and went off without a hitch. I knew that it would. Any update or fresh install I've ever done has given me no problems. PLEASE READ THE ENTIRE GUIDE BEFORE ATTEMPTING TO FOLLOW IT.
Download the latest UniBeast and run the application. After a series of continues and an agree, I selected my USB drive as the destination. Next select El Capitan. On Bootoader Configuration I've selected UEFI. Nothing was selected at the Graphics Configuration because this card is natively supported. Next I was presented with the Verify Installation Options screen. Select continue, and enter your password. It's now installation time. UniBeast creates a bootable USB drive, containing the installer and the Clover bootloader. As I was using a USB 3.0 device in a USB 3.0 port, this process was extremely fast; only taking a few minutes. After creation of your UniBeast installer, open it up in Finder and copy the Post Install folder that you downloaded from the Post Install Files section of this guide.
These are the BIOS setting I am using for this install.. Here are the highlights: BIOS is F14. X.M.P is set to Profile 1. I have set the Boot Mode to UEFI only as I have no Legacy installs in my multi booting setup. SATA is set to AHCI and XHCI is enabled. XHCI and EHCI Hand-off are both Enabled. Wake on LAN is Disabled.
INSTALLATION
System Changes
Open Clover Configurator - Right click > open > open. Along the bottom of the main window, you will see the path EFI > EFI > CLOVER > config.plist. Select the config.plist icon and you will be presented with the main Clover Configurator UI. Select SMBIOS from the options on the left. I use iMac 13,2 as the system definition. Alternatively you could use Mac Mini 6,x both similarly match for hardware and will work in achieving Native Power Management. Select the wand on the right side of the window and select the icon of the iMac. This brings up a new window with a drop down menu. Access it and select iMac 13,2. There are two "shake" buttons on the right side of the same window. Click each several times to generate a random Serial Number. Click ok to return to the main SMBIOS tab. Next select Boot, from the options on the left. Near the top right you will find an entry for Default Boot Volume. I want Clover to boot to the new installation, so I entered El Capitan 2. I also changed how long the system will remain at the Clover Boot Menu before Auto Booting my selected drive, by changing the Timeout to, 2 seconds. Thats it for Clover Configurator. Command+S to save to the original location and close the application.
CloverALC
Finally, to get audio working. The full guide relating to this subject can be found here: http://www.tonymacx86.com/audio/143757-audio-realtek-alc-applehda-guide.html. First thing you want to do is download (Raw) audio_cloverALC-110.command. Right click on the .command file > open > open. This will open up in Terminal. You are going to asked for your password (note: you will not get any visual feedback as you enter your password) Hit enter once you have completed entering your password. Next it will verify that you have SIP partially disabled, followed by a series of questions. Hit enter after you answer each question. The screenshot below shows the correct answers for the hardware specific to this guide. The command will run after the last answer has been entered. Once you are sure that it has completed you can close out terminal.
THAT COMPLETES POST INSTALL - TIME TO REBOOT
THINGS TO CHECK
USB STATUS
All USB 3.0 ports are working at 3.0 speeds. There are two USB 2.0 ports that are not working. One on the front of the case coming from the F_USB2 Header, and one off of the rear motherboard I/O. Im told this is because the system is over the 15 port limit. Screenshots show Sandisk Extreme plugged into the same USB 3.0 port that was used on the other El Capitan install, to create the UniBeast install media and to boot the system.
POST INSTALL FILES
Download the View attachment Post Install.zip which contains all of the required files and apps necessary for post install. Inside the .zip file, you will find one folder named Post Install. This folder should be copied to your UniBeast USB drive. I have also included the kext and app necessary to evaluate current CPU PM, as well as the HWMonitor app, as the required kexts are already in place for it. Your UniBeast USB file structure should look like the following.
Hope This Helps!
UPDATES
UniBeast 6.0 | Clover r3292 | OS X 10.11 El Capitan
This install guide is for the GA-Z77X-UD5H. I built this CustoMac in Early 2013. I have been through every update since 10.8 as well as major software upgrades 10.9, 10.10 and now 10.11. I participated in the 10.11 Public Beta releases through the GM release. This board has served me very well and I have rarely experienced any issue with it. I am running a triple monitor setup with dual GPUs. At the time of writing this guide there are no guides specific to this board, so I though "Why not?"
For the installation of 10.11 I used a blank 250GB SSD and did a clean install of OS X 10.11 El Capitan. For the most part I followed the UniBeast 10.11 Install Guide, only differing during post install. For post install I used the latest stand alone version of Clover r3292. Before the installation, I removed one of the GT 640s from my system, this was reinstalled after everything was up and running. The install was very smooth and went off without a hitch. I knew that it would. Any update or fresh install I've ever done has given me no problems. PLEASE READ THE ENTIRE GUIDE BEFORE ATTEMPTING TO FOLLOW IT.
PRE-INSTALL
After downloading El Capitan from the App Store, you are going to create your UniBeast install media. This guide requires the use of a 16GB USB drive, as we will be placing a post install folder on the drive. Alternatively you could use two 8GB drives, as long as, after formatting one of them has the required 7.45GB of free space. For testing purposes I used a 32GB USB 3.0 drive. This is not recommended practice as you may run into issue's using USB 3.0 and was only done as a test.
Download the latest UniBeast and run the application. After a series of continues and an agree, I selected my USB drive as the destination. Next select El Capitan. On Bootoader Configuration I've selected UEFI. Nothing was selected at the Graphics Configuration because this card is natively supported. Next I was presented with the Verify Installation Options screen. Select continue, and enter your password. It's now installation time. UniBeast creates a bootable USB drive, containing the installer and the Clover bootloader. As I was using a USB 3.0 device in a USB 3.0 port, this process was extremely fast; only taking a few minutes. After creation of your UniBeast installer, open it up in Finder and copy the Post Install folder that you downloaded from the Post Install Files section of this guide.
These are the BIOS setting I am using for this install.. Here are the highlights: BIOS is F14. X.M.P is set to Profile 1. I have set the Boot Mode to UEFI only as I have no Legacy installs in my multi booting setup. SATA is set to AHCI and XHCI is enabled. XHCI and EHCI Hand-off are both Enabled. Wake on LAN is Disabled.
INSTALLATION
I inserted the UniBeast installer into a USB 3.0 port coming from the front, F_USB30_3 header. Again this method is not recommended and if you choose to go this route and run into any issues, I would first recommend switching to a USB 2.0 drive placed into a USB 2.0 port. I rebooted the system, continually pressing the hotkey (Delete) to get into the BIOS. Once in the BIOS, I made the above BIOS changes. Next I chose save and exit > reboot. This time I continually pressed the hotkey (F12) to reach the BIOS boot menu. From the BIOS boot menu I selected UEFI USB HDD. With the boot mode set to UEFI only the selection choices are obviously reduced, thus making the correct selection easier, if you've ever been unsure about what option to select.
Booting from UEFI USB HDD sends me to the tonymacx86 Clover boot menu. At the boot menu, I used the arrow keys until I reached: Boot Mac OS X from USB. No additional boot arguments were used. Once this option has been selected I hit enter and this took me to the installer.
Once in the installer, I erased and formatted the drive I was going to be installing on. For full instructions, see the UniBeast 10.11 Install Guide. Basically you are going to use Disk Utility to format the drive, Extended (Journaled), GUID Partition Map. I named my partition El Capitan 2. Upon closing Disk Utility, I was asked where I wanted to install and I chose El Capitan 2. The install took about 20 minutes. Upon completion the system auto reboot.
On the reboot you are going to want to once again use the hotkey (F12) to get into the BIOS boot menu. Again I selected UEFI USB HDD. Booting from UEFI USB HDD again takes me to the Clover boot menu. At the boot menu, I chose: Boot Mac OS X from El Capitan 2. Next was the setup process, it is pretty self explanatory. The two things I will note are to not sign in with your AppleID, we do not not want to log any information about this CustoMac with Apple until we have setup iMessage. Also do not Transfer Information to This Mac. You can use Migration Assistant to do this later. Next I was presented with the desktop. Time for post install.
POST INSTALLATION
(See Updates Below)
Installing Clover Bootloader
First we are going to install Clover to the system drives EFI partition. Run the Clover_v2.3k_r3292.pkg, by right click > open > open. Select Continue > Continue. Then, Change Install Location and select your system drive. In my case it was El Capitan 2. Select Customize. See the screenshots below for the correct options to choose (Note: Under Action yours will say install, where these say upgrade. Forgot to take screenshots originally). Finally click install. When the install is finished you will be presented with Installation Complete window. Close the program. The Clover installer will leave the EFI partition mounted. This is essential for the other post install tasks. Last thing to do in this section is to replace the EFI folder that Clover Created in the EFI partition, with the one in your Post Install folder, located on your Desktop.
Navigate to: /EFI and replace the ENTIRE EFI folder with the EFI folder from your Post Install folder.
Booting from UEFI USB HDD sends me to the tonymacx86 Clover boot menu. At the boot menu, I used the arrow keys until I reached: Boot Mac OS X from USB. No additional boot arguments were used. Once this option has been selected I hit enter and this took me to the installer.
Once in the installer, I erased and formatted the drive I was going to be installing on. For full instructions, see the UniBeast 10.11 Install Guide. Basically you are going to use Disk Utility to format the drive, Extended (Journaled), GUID Partition Map. I named my partition El Capitan 2. Upon closing Disk Utility, I was asked where I wanted to install and I chose El Capitan 2. The install took about 20 minutes. Upon completion the system auto reboot.
On the reboot you are going to want to once again use the hotkey (F12) to get into the BIOS boot menu. Again I selected UEFI USB HDD. Booting from UEFI USB HDD again takes me to the Clover boot menu. At the boot menu, I chose: Boot Mac OS X from El Capitan 2. Next was the setup process, it is pretty self explanatory. The two things I will note are to not sign in with your AppleID, we do not not want to log any information about this CustoMac with Apple until we have setup iMessage. Also do not Transfer Information to This Mac. You can use Migration Assistant to do this later. Next I was presented with the desktop. Time for post install.
POST INSTALLATION
(See Updates Below)
Post installation is going to consist of 3 parts. Installing the Clover Bootloader, Changes to system definition and boot options using Clover configurator, and configuring onboard audio. From your UniBeast USB, copy the Post Install folder to the desktop. Do not reboot until all post installation tasks have been completed.
Installing Clover Bootloader
First we are going to install Clover to the system drives EFI partition. Run the Clover_v2.3k_r3292.pkg, by right click > open > open. Select Continue > Continue. Then, Change Install Location and select your system drive. In my case it was El Capitan 2. Select Customize. See the screenshots below for the correct options to choose (Note: Under Action yours will say install, where these say upgrade. Forgot to take screenshots originally). Finally click install. When the install is finished you will be presented with Installation Complete window. Close the program. The Clover installer will leave the EFI partition mounted. This is essential for the other post install tasks. Last thing to do in this section is to replace the EFI folder that Clover Created in the EFI partition, with the one in your Post Install folder, located on your Desktop.
Navigate to: /EFI and replace the ENTIRE EFI folder with the EFI folder from your Post Install folder.
System Changes
Open Clover Configurator - Right click > open > open. Along the bottom of the main window, you will see the path EFI > EFI > CLOVER > config.plist. Select the config.plist icon and you will be presented with the main Clover Configurator UI. Select SMBIOS from the options on the left. I use iMac 13,2 as the system definition. Alternatively you could use Mac Mini 6,x both similarly match for hardware and will work in achieving Native Power Management. Select the wand on the right side of the window and select the icon of the iMac. This brings up a new window with a drop down menu. Access it and select iMac 13,2. There are two "shake" buttons on the right side of the same window. Click each several times to generate a random Serial Number. Click ok to return to the main SMBIOS tab. Next select Boot, from the options on the left. Near the top right you will find an entry for Default Boot Volume. I want Clover to boot to the new installation, so I entered El Capitan 2. I also changed how long the system will remain at the Clover Boot Menu before Auto Booting my selected drive, by changing the Timeout to, 2 seconds. Thats it for Clover Configurator. Command+S to save to the original location and close the application.
CloverALC
Finally, to get audio working. The full guide relating to this subject can be found here: http://www.tonymacx86.com/audio/143757-audio-realtek-alc-applehda-guide.html. First thing you want to do is download (Raw) audio_cloverALC-110.command. Right click on the .command file > open > open. This will open up in Terminal. You are going to asked for your password (note: you will not get any visual feedback as you enter your password) Hit enter once you have completed entering your password. Next it will verify that you have SIP partially disabled, followed by a series of questions. Hit enter after you answer each question. The screenshot below shows the correct answers for the hardware specific to this guide. The command will run after the last answer has been entered. Once you are sure that it has completed you can close out terminal.
THINGS TO CHECK
AUDIO FUNTION
Navigate to system preferences and select sound. On the output tab, the section to select an audio device for sound output should be populated with four choices. If the section remains unpopulated, see No Audio Devices - Realtek ALC AppleHDA for more information. The first "Line Out" device in the list, and its corresponding black or "Rear Speaker Out" jack on the motherboard I/O, are the correct selections for enabling audio. However, if these do not provide working audio, check other possible combinations of audio device and I/O jack (green/grey/orange). If all other combinations fail to provide working audio, see No Sound - Realtek ALC AppleHDA for more information.
NATIVE CPU POWER MANAGEMENT
The complete guide is located here: Native CPU/IGPU Power Management. While I thought about explaining how to setup CPU Power Management in this guide, I ultimately decided it would be best to show that Native PM is possible with this setup, and how to check your current values, so you can decide how pertinent implementing a fix would be. To check your current CPU P-States, place AppleIntelCPUPowerManagementInfo.kext in /EFI/EFI/CLOVER/kexts/Other and reboot. In Terminal, run
Good news for any of you that are running an i7 3770K, or a i7 3770, as I have done the work for you. The SSDT's are located in the Post Install, Files folder, in individual folders titled by CPU. Select the correct SSDT and place in /EFI/EFI/CLOVER/ACPI/patched. As you can see, this build is returning all P-States. Do not be alarmed if the top end P-States are not showing. As RehabMan explained to me "Per Intel spec, some of the top turbo states require only a single core to be active." The two Intel Power Gadget screenshots I have included, show the system at rest (left) and under load for a short period of time (right). I used handbrake to introduce the load.
Navigate to system preferences and select sound. On the output tab, the section to select an audio device for sound output should be populated with four choices. If the section remains unpopulated, see No Audio Devices - Realtek ALC AppleHDA for more information. The first "Line Out" device in the list, and its corresponding black or "Rear Speaker Out" jack on the motherboard I/O, are the correct selections for enabling audio. However, if these do not provide working audio, check other possible combinations of audio device and I/O jack (green/grey/orange). If all other combinations fail to provide working audio, see No Sound - Realtek ALC AppleHDA for more information.
NATIVE CPU POWER MANAGEMENT
The complete guide is located here: Native CPU/IGPU Power Management. While I thought about explaining how to setup CPU Power Management in this guide, I ultimately decided it would be best to show that Native PM is possible with this setup, and how to check your current values, so you can decide how pertinent implementing a fix would be. To check your current CPU P-States, place AppleIntelCPUPowerManagementInfo.kext in /EFI/EFI/CLOVER/kexts/Other and reboot. In Terminal, run
Code:
cat /var/log/system.log | grep "AICPUPMI:"
Good news for any of you that are running an i7 3770K, or a i7 3770, as I have done the work for you. The SSDT's are located in the Post Install, Files folder, in individual folders titled by CPU. Select the correct SSDT and place in /EFI/EFI/CLOVER/ACPI/patched. As you can see, this build is returning all P-States. Do not be alarmed if the top end P-States are not showing. As RehabMan explained to me "Per Intel spec, some of the top turbo states require only a single core to be active." The two Intel Power Gadget screenshots I have included, show the system at rest (left) and under load for a short period of time (right). I used handbrake to introduce the load.
USB STATUS
All USB 3.0 ports are working at 3.0 speeds. There are two USB 2.0 ports that are not working. One on the front of the case coming from the F_USB2 Header, and one off of the rear motherboard I/O. Im told this is because the system is over the 15 port limit. Screenshots show Sandisk Extreme plugged into the same USB 3.0 port that was used on the other El Capitan install, to create the UniBeast install media and to boot the system.
POST INSTALL FILES
Download the View attachment Post Install.zip which contains all of the required files and apps necessary for post install. Inside the .zip file, you will find one folder named Post Install. This folder should be copied to your UniBeast USB drive. I have also included the kext and app necessary to evaluate current CPU PM, as well as the HWMonitor app, as the required kexts are already in place for it. Your UniBeast USB file structure should look like the following.
UPDATES
Updated to OS X 10.11.1
October 25, 2015 - Successful update via MAS. Update did not affect USB 2.0/3.0. Audio remained after update |
MultiBeast 8
Now that MultiBeast 8 has been released, I thought that I would provide the View attachment Z77X-UD5H.mb file to facilitate those that want to do post install with MultiBeast. This will allow you to essentially skip all of the Post Install steps above. MultiBeast can install Clover, set the default boot drive and timeout to 3 seconds, as well as configure the onboard ALC898 audio.
Now that MultiBeast 8 has been released, I thought that I would provide the View attachment Z77X-UD5H.mb file to facilitate those that want to do post install with MultiBeast. This will allow you to essentially skip all of the Post Install steps above. MultiBeast can install Clover, set the default boot drive and timeout to 3 seconds, as well as configure the onboard ALC898 audio.
Updated to OS X 10.11.2
December 9, 2015 - Successful update via MAS. Update did not affect USB 2.0/3.0. Audio remained after update |