Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

[CaseySJ]

HI thanks again for your great work

is it possible to integrate the last version of intelmausiethernet.kext

GitHub - Mieze/IntelMausiEthernet: OS X driver for Intel onboard LAN

OS X driver for Intel onboard LAN. Contribute to Mieze/IntelMausiEthernet development by creating an account on GitHub.

github.com

2.5.3d3 so far (instead of 2.5.1d1)

as i have bugs with 2.5.1d1

thanks

Hello @epalzeo,

We have switched to IntelMausi.kext by Acidanthera, which is located here.

 

[CaseySJ]

Sigh. Screwed up a perfectly working system...

Okay. So, after sitting around and not doing much with updating OpenCore for 6 months, I finally got off my butt and updated to the latest. It worked fine, which was great, but while doing so, I noticed that I had two EFI partitions, named the same, on my boot drive (I dual boot Windows).

Are you sure there were two EFI partitions on the same physical SSD? Is that SSD segmented into a macOS partition and a Windows partition?

One of them had the Open Core stuff I expected. The other one appeared empty. Thinking it wasn't doing anything, I deleted the partition.

All seemed well, until I tried to boot into Windows. Open Core shows the drive, I have the option to pick it, but when I go to boot, it just goes into a black screen.

To be clear, OpenCore does show a boot icon for Windows? But after you select Windows, the screen goes black? If so, please follow the procedure to disable AppleVTD (4 posts above this). Then see if Windows will boot.

On the other hand, if I use the BIOS boot-picker, I can boot into Windows with no issues. I could, I suppose, continue to do this, but it's inelegant and I'd prefer to OC boot-picker to work.

Any suggestions?

Thanks!

 

[sweetphreak]

@sweetphreak,

Some questions:

• Which version of OpenCore is on your original USB install disk?
• Which version of OpenCore were you running before attempting the update to 0.7.2?
• If you can post the config.plist from OpenCore 0.7.2 and your USB install disk, I can take a look. (Remove serial numbers from PlatformInfo section before posting the files.)

I updated the USB with my latest working EFI. HackindROM reports it to be 0.7.0 but I think at some point I screwed up the version in an update. Still, it works... so, I the version that was working previous to updating to 0.7.2 is the same one I have in my USB stick.
So I´m attaching here the version that works OK with 0.7.0. The one I´m trying to use is the same one that´s in this guide, which I assume is the same as the one HackindROM creates. Right?
Also, I attached the log again just in case.

 

[sweetphreak]

What version of OC were you using to get wifi and bluetooth running? I am on OC 0.6.8, but no Bluetooth and wifi working.

As I said in my previous post. I think it´s 0.7.0... but it was working well with the bluetooth kexts provided in this guide. Open Intel wireless and bluetooth has always worked for me.

 

[yurid]

CaseySJ​

Thank you for the excellent guide. Not very often these days a one can find this kind of writing. Very well structured, comprehensive. Reading and following was an absolute joy. I built the rig a week ago, everything seemed to be working, but I didn't have a chance to verify it thoroughly, for I had to fly south of the border for two weeks.

 

[Ayvan]

Thank you
However, it seems to be worse

Do you have an overlock, custom LLC settings?

 

[cooolbreizha]

Is this happening at all sampling rates or only at high rates (192 KHz)? Please have a look here to see if this is the same problem that you're experiencing:

Gigabyte Z490 Vision D (Thunderbolt 3) + i5-10400 + AMD RX 580

Always willing to help if I can. I do not have a dual boot system setup however I do have a VM Windows 10 Installed using VirtualBox. Not sure if it will work through that but am willing to give it a try. I already tested this on Parallels Desktop, even with a directly connected to VM Windows...

www.tonymacx86.com

Hello @CaseySJ
It was exactly my problem:
44.1 & 48kHz seems to work
88.2 & 96kHz squealing and random distortions
Beyond that, only frying!

I kept the "CPU Base Clock" setting at 100.0 MHz (not auto) as @Ayvan advised me.
Uninstalled / Reinstalled the UAD program.

Sounds good to me, I can switch between different sample rates and up to 192.
Maybe I installed it in a hurry, I don't remember.

Thank you very much for your help which UAD refused to give me.
You were essential in the construction of my project

 

[jonpm]

I've been thinking about building a new system for a while and started pricing up components today. I'm struggling to find the Z490 Vision D in stock anywhere (I live in Switzerland btw) so was wondering has it been discontinued? Or is this just another case of the general shortage of components etc?

 

[CaseySJ]

I've been thinking about building a new system for a while and started pricing up components today. I'm struggling to find the Z490 Vision D in stock anywhere (I live in Switzerland btw) so was wondering has it been discontinued? Or is this just another case of the general shortage of components etc?

Yes I believe Z490 series boards are largely discontinued. When existing inventory dries up, they will be gone, but should appear on the used market.

 

[ckrueger99]

An alternative is the ASRock W480 Creator. There seems to be more inventory. Lacks overclocking but has 10G ethernet. ASRock W480 Build