- Joined
- May 14, 2013
- Messages
- 2
- Motherboard
- Mountain Lion 10.8.3
- CPU
- Intel i7 3770K
- Graphics
- Zotac Gtx660 2GB
- Mac
- Classic Mac
- Mobile Phone
Hello all,
I have installed my OSX in my PC successfully, but I have a problem. When I run IFCONFIG it only appears the following:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4>
ether bc:5f:f4:4a:c8:cb
inet6 fe80::be5f:f4ff:fe4a:c8cb%en0 prefixlen 64 scopeid 0x4
inet 192.168.2.4 netmask 0xffffff00 broadcast 192.168.2.255
media: autoselect (100baseTX <full-duplex,flow-control>)
status: active
I have plugged a firewire card with a RME FireFace 400 and it is working, but FW0 device does not appear. I want it to appear because sometimes the audio card does not boot properly (host led remains in red) and I have to manually turn off and on the card to make it work so I was thinking about program
ifconfig fw0 down
ifconfig fw0 up
with automator during each booting in order to "fix" the problem..
Any idea?
Thanks in advance!
Mario.
I have installed my OSX in my PC successfully, but I have a problem. When I run IFCONFIG it only appears the following:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4>
ether bc:5f:f4:4a:c8:cb
inet6 fe80::be5f:f4ff:fe4a:c8cb%en0 prefixlen 64 scopeid 0x4
inet 192.168.2.4 netmask 0xffffff00 broadcast 192.168.2.255
media: autoselect (100baseTX <full-duplex,flow-control>)
status: active
I have plugged a firewire card with a RME FireFace 400 and it is working, but FW0 device does not appear. I want it to appear because sometimes the audio card does not boot properly (host led remains in red) and I have to manually turn off and on the card to make it work so I was thinking about program
ifconfig fw0 down
ifconfig fw0 up
with automator during each booting in order to "fix" the problem..
Any idea?
Thanks in advance!
Mario.