1) extracted a fresh appleHDA.kext with Pacifist from the Sierra installer and replace the existing S/L/E/appleHDA.kext with it
2) downloaded "audio_cloverALC-120_v1.0d.command" from the link above
3) run the commandfile with answers: 283, inject, 1
4) remove appleACL from Clover & reboot.
I'm running High Sierra right now. I've done an upgrade from Sierra. Just don't forget to put apfs.efi in your clover driversAny brave man/woman tried to install High Sierra yet?
I'm looking forward to rebuild my D34010WYK and use it, but there's the new filesystem and always some specific kext updates.
Thanks ethermcman. In my case I’ll start from scratch with high Sierra. Can I follow the same steps of the Sierra install and just add the kexts you mentioned?I'm running High Sierra right now. I've done an upgrade from Sierra. Just don't forget to put apfs.efi in your clover drivers
For audio, just use audio_cloverALC-130.sh from around.
All is running well except that the Arabesque screensaver is buggy and laggy.
Hi,I'm running High Sierra right now. I've done an upgrade from Sierra. Just don't forget to put apfs.efi in your clover drivers
For audio, just use audio_cloverALC-130.sh from around.
All is running well except that the Arabesque screensaver is buggy and laggy.
You can follow the Sierra's steps from Sebinouse. Just delete SSDT-HDEF.aml, put apfs.efi in clover drivers and run udio_cloverALC-130.sh.Thanks ethermcman. In my case I’ll start from scratch with high Sierra. Can I follow the same steps of the Sierra install and just add the kexts you mentioned?
What about that new EFI check in High Sierra, is it a problem?
https://www.macobserver.com/news/macos-high-sierra-performs-efi-security-check/
Hi,
I performed upgrade from sierra (10.12.6) to high sierra 10.13 and everythings appear good except for HDMI audio.
I tried followed methods:
1) vit9696 (lilu + applealc)
2) toleda patch (audio_cloverHDMI-130.command)
3) voodoohda (2.8.8)
but my system stays muted.
Any suggestion is welcome.
Many thanks.
How did you manage to change the layout-id? I've tried with MacIASL but it doesn't save my modifications.Salut Sebinouse, hello everyone, thank you all for your valuable comments and feedback! I have a couple of questions after successfully setting up my Intel D54250WYKH NUK with vanilla Sierra 10.12.6 (2x4GB RAM, Samsung 128GB m2.SSD and 500GB SATA SSD). The BIOS was updated to v45 from Intel and set properly; the PCI-card for WLAN is Atheros AR9280 (from eBay) for OOB use with minor device-id tweaking via Clover.
After creating the setup USB drive and installing Sierra 10.12.6 directly, I installed only the following kexts in /Library/Extensions/
a) Latest FakeSCM (v1426) and plugins (from www.hwsensors.com but now only at www.github.com/kozlek/HWSensors)
b) Latest AppleALC v1.1.4 and Lilu 1.1.7 (set layout-id as 0x01 in SSDT-HDEF.aml)
c) IntelMausiEthernet driver for LAN (v2.3.0)
d) IntelGraphicsFixup v1.1.7 (just today!)
Thanks Sebinouse for pointing out the "IntelGraphicsFixup.kext" solution some pages ago, I must have missed that one out, I also had Safari freezing over some pages with embedded video and wasn't sure what was causing it; hope this is fixed now forever.
1) Any idea if we still need to use SSDT-HACK.aml file with BIOS v45 now? What is the region fix exactly? (mentioned in first post)
2) For native detection of IGPU, I am using ig-platform-id of {0x03, 0x00, 0x22, 0x0D} for some reason, but I see you are using {0x0D, 0x00, 0x26, 0x0A} instead; any preference or reason to choose the correct one? I could not find more info on the differences... originally I thought this was the reason for the Safari-freeze...
3) Compared to other threads where there is huge talk about USB ports and compatibility and patching etc. (I have no experience and no idea how to resolve) I see that nobody really dealt with USB ports and fixing for this NUC; am I correct in assuming that we don't need such solution i.e. all ports on this NUC work 100% OK without any sort of injection or patching? (e.g. FakePCIID.kext by RehabMan that I see is widely used)
I enabled the FixShutdown_0004 in Clover as you suggested Sebinouse, as the NUC wouldn't shutdown completely if I left some USB drives attached; but now I have the wireless Logitech M175 mouse freezing when moving
4) Anyone has tried for a long time the FakeSMC branch of RehabMan instead of Kozlek's known branch?
Thanks in advance to everyone, once more.
Thanks for your suggestions.I've tried the lilu+applealc which should be the best way but I've never managed to make it work.
The voodoo path is the simplest but sometimes sound is humming or weird.
The Toleda path is the best for me but you have to re-patch when a new MacOS appears. Just remember to delete SSDT-HDEF.aml like I've said in previous post but again I'm not using HDMI sound.