Contribute
Register

Almost success! Doesn't want to boot after Multibeast.

Status
Not open for further replies.
Patrik1972 said:
Nice, it worked but I had to go in and change the System Intergrity Configuration from 0x0003 to 0x0067. Can I change that in config.plist with Clover Configurator so I don't have to do that every time?
Click to expand...
Of course.

SIP.png
 
OK, but where? There isn't any section called in the Configurator. This is the first time I'm building a Hackintosh. Sorry for all the questions!
 
P1LGRIM said:
See Post #21.
Click to expand...
Sorry, there was a delay on the picture. Didn't see it until now. ;)
Thank you!

So, what do I do now?
I still don't have any sound and I haven't installed my GPU.
 
Patrik1972 said:
So, what do I do now?
I still don't have any sound and I haven't installed my GPU.
Click to expand...
Fix your sound and install your graphics card.
 
P1LGRIM said:
Fix your sound and install your graphics card.
Click to expand...
Haha...
That's what I tried the last time when it screwed up Clover. I'm back now where I was in Post #3. Don't want that to happen again.
 
Patrik1972 said:
Haha...
That's what I tried the last time when it screwed up Clover. I'm back now where I was in Post #3. Don't want that to happen again.
Click to expand...
Well, now you know how to fix it.

For assistance with Audio you should post in the Audio forum.
Read the 'sticky' guides first and be sure to comply with the Problem Reporting instructions or you will not get any help.

For your graphics :
BIOS - Disable Integrated graphics - Set PEG as Primary
Use a digital connection - DVI or HDMI - VGA is not supported.
Boot with nv_disable=1
May need to update Clover
Install web drivers
Update web drivers to ensure that you have the correct version.
Config.plist - Do not inject Intel or Nvidia graphics and no ig-platform-id
Config.plist - Disable SIP completely - CsrActiveConfig 0x67
Edit config.plist - NvidiaWeb = true as per Link
May need to emulate native NVRAM - Problem 6 - Install EmuVariableUefi-64 and RC scripts or install AptioMemoryFix or OsxAptioFixv3
Remove nv_disable=1 from config.plist
May need to install Lilu.kext , LiluFriend and NvidiaGraphicsFixup.kext

Potential Problems :
HDMI 2.0 is not supported - Use HDMI 1.4 (or lower)
If your graphics card has more than one output of the type that you are using then try another one.
Black Screen with MacPro 6,1 or iMac 15 or iMac 17 System Definition
 
Last edited:
P1LGRIM said:
Well, now you know how to fix it.

For assistance with Audio you should post in the Audio forum.
Read the 'sticky' guides first and be sure to comply with the Problem Reporting instructions or you will not get any help.

For your graphics :
BIOS - Disable Integrated graphics - Set PEG as Primary
Use a digital connection - DVI or HDMI - VGA is not supported.
Boot with nv_disable=1
May need to update Clover
Install web drivers
Update web drivers to ensure that you have the correct version.
Config.plist - Do not inject Intel or Nvidia graphics and no ig-platform-id
Config.plist - Disable SIP completely - CsrActiveConfig 0x67
Edit config.plist - NvidiaWeb = true as per Link
May need to emulate native NVRAM - Problem 6 - Install EmuVariableUefi-64 and RC scripts or install AptioMemoryFix and OsxAptioFixv3
Remove nv_disable=1 from config.plist
May need to install Lilu.kext , LiluFriend and NvidiaGraphicsFixup.kext

Potential Problems :
HDMI 2.0 is not supported - Use HDMI 1.4 (or lower)
If your graphics card has more than one output of the type that you are using then try another one.
Black Screen with MacPro 6,1 or iMac 15 or iMac 17 System Definition
Click to expand...
Yes, your right! I've learn that now incase that happens again. :)

It's almost 1:30am here now so I have to go to bed, but thank you for all your advices! Really appreciate it!
 
Hi Patrik, I have the same MSI Z270-A Pro mainboard and I am planning to install 10.13.4 due to native support for amd cards. (I own rx 580)
However, there is not much information for this mainboard in the forum. There are little bits and pieces of information spread around but it is very hard to follow.
Could you please summarize your experience so we can have a base to start? E.g. how did you start and what parameters you used?
Thanks in advance.
 
Status
Not open for further replies.
Copyright © 2010 - 2024 tonymacx86 LLC
Back
Top