I hope this is the right part of the forum to post this message on.
I had an iMac die a few months ago and the only thing I could salvage from it was the SSD with High Sierra installed , which is now attached to my new system. During playing around with clover and trying to install...
Hello there, I have managed to install MacOs Sierra on my Asus X550vc, but the thing is I am only able to boot into it by Clover installed on USB. I have installed clover bootloader to the SSD MacOs is on, but the whole SSD is not recognized by my BIOS. I am clueless, what can I do about it...
Hi guys, so I’ve been looking for an affordable good ssd for my Dell XPS 15 9750, I have found the Addlink S70 1TB, but wondering about its compatibility with Catalina.
Does anybody here have tried it, what’s the result? Thanks a lot
Hi there, I am new to the world of Hackintoshing and this forum so I'm sorry if its in the wrong place.
I just built my first Hackintosh (Lenovo 1440p Laptop) and I want to upgrade its HHD to an SSD soon. Is there a tool or any easy way to make an exact copy of the current Lenovo HDD with all...
Greetings. My configuration is as follows:
Motherboard: Asrock h61m-vg3
CPU: i5 2500
GPU: RX 470 XFX 4GB
Ram: 8 gb
Storage: SSD TeamGroup GX1 120GB
Power Supply: Cooler Master 550w
OS: macOS Mojave
My problem is the following. I have successfully installed macOS Mojave on my SSD, but after...
I have TP-Link Archer T9E 802.11AC AC1900 + Crucial P1 1TB 3D NAND NVMe PCIe M.2 SSD - CT1000P1SSD8.
When I use both the tp-link works but the crucial nvme doesn't work and the motherboard doesn't recognize it. If I unplug the tp-link archer then the SSD works. I've used and test...
Hi, as shown above are the error messages I received before the system reboots after a few minutes in the install screen where 15 minutes remaining are shown.
So what I’ve done is booted off the USB, installed macOS and then tried to boot off the SSD to complete the setup but it just restarts...
I have successfully installed and dual-booting win10 on a small SSD, and High Sierra on a mechanical HDD.
I am experiencing that my MacOS install has significantly slower performance than my windows installation, and I expect it is because of the hdd its installed on.
My plan is to upgrade...
Just got Addlink S70 1TB NVMe PCIe Gen3x4 1TB SSD.
Didn't find any info on compatibility, so took the risk!
Successfully installed it into my XPS 9570 and have Mojave 10.14.6 working perfectly.
For some of you in...
I'm planning to build an Hackintosh x299 based and I was wondering if I can use one SSD PCIe 3.0 expansion card to build a RAID 0 system disk like one of there:
- ASRock Ultra Quad M.2 Card
- M.2 XPANDER-AERO
Tks a lot in advance
Hi all, first time poster. I have an OWC SATA SSD previously used as the only hard drive on a 2011 Macbook pro. The Macbook no longer works due to GPU issues, but the SSD still works, usable on my 2012 Mac Pro tower. If I were to buy a NUC and use the SATA SSD as my hard drive, would it just...
Good morning wonderful community.
Yesterday I was having some problems with my hackintosh and couldn’t have a better idea than enabling trim with the terminal command sudo trimforce enable.
After that I wasn’t able to boot the system anymore. It gets stuck at the apple logo.
I have a Mojave-based system installed on 970 EVO Plus. All looks good on every speed tests, like Blackmagic (see a screenshot). Also I've installed iStat Menus which shows me that the write/read speed is limited near 450-500 MB/s during moving/copying files from external USB 3.1. or unpacking...
So I'm trying to install macOS High Sierra on my Dell XPS 8910, I have successfully done this, but it was on a spare mechanical sata hard drive, now that I have comfirmed that macOS runs fine on it I want to install it on the internal NVMe ssd, however it does not show up in disk...
I am planning on buying one of these two models of SSD I can only afford these models, but I am concerned are they going to work well and for the long run If:
1. Install macOS Mojave or High Sierra with APFS
2. Dual Boot macOS Mojave with Windows 10
3. Still getting the feel of fast SSD...
So I went to update to 10.14.5.
I updated clover to the latest build, and started the update from the app store, once the system rebooted clover no longer shows my drive anymore. I verified in the bios thats its still their and also tried the clover cli to see if the EFI partition for my drive...
Samsung 970 PRO 512GB - NVMe PCIe M.2 2280 SSD (MZ-V7P512BW)
Samsung 960 EVO 500GB Solid State Drive (MZ-V6E500BW) m.2 NVMe
I'm looking at these 2 SSDs, they're both NVMe m.2 drives, one is 970 and one is 960. Why is the 960 more expensive? what am I missing?
Hello everyone, I built my very first hackintosh and it works quite smoothly at the moment. But I have noticed something that my SSD is not working as the others, when I measured my writing/reading speeds, I am getting very stable 1.500~ each writing and reading speed but I believe my reading...
I have two SSD
1. Samsung SSD 860 EVO 500GB
2. Kingston K-98-UV500
When I boot with Bootable Mojave USB, my Samsung SSD show but with the same cable, my Kinston SSS becomes uninitialized.
And same with my Internal 7200 RPM HDD. I not able to install on both.. I do not want to install it on...