multibeast

I installed Catalina 10.15.4 on my Dell Optiplex 5060 (i7 8700 intel UHD 630) with no issues. After running multicast I get stuck when booting with the error "Graphics Driver Failed to Load: Could not register with Framebuffer driver". Shouldn't there be native support for the UHD 630?

MultiBeast, the ultimate post-installation utility, has been updated to version 12.3.0 for macOS Catalina 10.15.5+. MultiBeast is an all-in-one post-installation utility designed to enable boot from a hard drive. It also features a collection of drivers and customization options. Please make...

MultiBeast, the ultimate post-installation utility, has been updated to version 12.2.0 for macOS Catalina 10.15.5+. MultiBeast is an all-in-one post-installation utility designed to enable boot from a hard drive. It also features a collection of drivers and customization options. Please make...

Hello everyone, I am a young developer that needs to use xCode. I created an macOS Catalina bootable USB using Unibeast and have installed macos succesfully on a usb thumb drive (I want to test my hackintosh in a usb stick first, before I install it on my hdd). My setup: a intel core i7 @ 3,6...

Preface: My system (reference Cheese Grater II configuration in my signature) does not support native VRAM, thus Emulated VRAM is required. Before upgrading to macOS 10.15.4, I used Multibeast 12.1.0 to install a new Clover bootloader with Emulated VRAM by doing the following: 1) Launch...

MultiBeast, the ultimate post-installation utility, has been updated to version 12.0.0 for macOS Catalina 10.15.3+. MultiBeast is an all-in-one post-installation utility designed to enable boot from a hard drive. It also features a collection of drivers and customization options. Please make...

Hi, I just followed the guide to install Catalina on an Intel based pc. I've done all the installation successfully but I need to install the drivers and the boot loader with Multibeast. The problem is: there's no Multibeast for Catalina. I tried to use the Mojave version but Multibeast failed...

Hi folks! I need some help with my build if someone can guide me. I've successfully installed Mac os in my build: Gigabyte Aorus Z390 Pro Wifi Intel Core i7 9700K Ballistix Sports 32Gb Sapphire Radeon RX 580 Pulse ABWB Wifi/Bluetooth Card So I did installed Mac OS Mojave using Unibeast (Clover...

This is the issue in verbose mode - My config is - i5 9600K - z390m - crucial ddr4 2133mhz - samsung 960 evo m.2 - rx 560( in which I plugged the hdmi port ) I have made it into the post installation step ( though there were ocasions when the booter restarted the pc ) And made a SMBIOS...

Ok, I almost got it. Working for literally 4 month. ASUS Vivo AiO V221IC. All I got Post-Installation with MultiBeast. I selected all the options I needed. Clicked install The installation failed. Help. MultiBeast option and log in the RTF TXT file. _____ macOS Version: macOS Catalina 10.15.0...

I got through the install and the OS looked good. I did the post install Step of the guide and loaded Multibeast with some settings I thought I would need. (Not really sure how to tell what I need) Now when I boot from the SSD it goes to the Apple logo, the bar goes about half way, and then...

I'm at that part on multibeast where i should choose some drivers but i don't know wich ones are compatible with my motherboard. it is a gsuo h61v10c and since it's a generic version, doesn't have any info online. :( can someone give me a hand, please? btw the chipset it's the same of the...

Hi, I have an Intel DQ77MK Mobo which is working well with OSX 10.8.5 (for legacy apps), OSX10.10 Yosemite and a slightly buggy OSX10.12 Sierra. Now I've just built a couple of High Sierra Installs - one on an SSD in HFS+ format, and a 2nd SSD in APFS format. These SSDs were blessed using...

Hi my friends, I'm trying to install MacOs-Mojave on a Hp EliteDesk 800 G2 Sff (IntelCore i7vpro, 16GB RAM, 512GB SSD Samsung) when the mac os is installing and then time to finish is remaining at approx. 2 minutes the PC is restarting and I get this error: Please, friends, any help or...

After a successful install of Mojave, I ran MultiBeast to install the boot loader to the hard drive. After I restarted the computer it was looping the clover boot loader over and over. On MultiBeast I used 1. Quick start - UEFI Boot Mode 2. Audio - AppleALC 3. Disk - 3rd party SATA 4. Network -...

I know there are many users like me stuck @ HS because of Nvidia GPUs. (and happy with it) Don't we deserve latest bootloader and kexts? Is there any plan about new Unibeast&Multibeast for 10.13.6? (I post that probably in wrong section)

I was able to get Mojave installed(I verified the hard drive) but I need the the USB to boot into it. Will running MultiBeast fix the issue? Or can it be done thru the Terminal? I really don't wanna reinstall again but can if I really need to. Also under MultiBeast SMBIOS iMac 17.1 is listed...

Hi, Already reinstalled macOS Mojave for the fifth time now. Because somehow i’m doing something wrong with multibeast. I checked UEFI. For audio I checked AppleALC. For disk i selected everything. Miscellaneous checked the HWMonitor, Powermanagment and the plug-ins. For ethernet I...

Hello there, This is my first Hackintosh and I will listen to all the recommendations of this community. I have created a bootable USB with macOS High Sierra Installer using Unibeast and successfully managed to install macOS High Sierra on my HDD. Posteriorly, I used Multibeast for the post...

Hi, I would like to upgrade my rig [profile specs], from el Capitan to High Sierra, and would love some insight before I begin. I have read through the install guide [https://www.tonymacx86.com/threads/update-directly-to-macos-high-sierra.232707/] And I have combed through numerous posts on...