1. clarkdv

    H61N-USB3 upgrading from i3 to i5

    I have a Gigabyte H61N-USB3 with a i3-2105 currently running High Sierra. I'm about to remove the i3 and install a i5-3570K. Is that all I need to do or do I need to set anything differently in the BIOS? Thanks!
  2. guido79

    Gigabyte H61N-USB3 - El Capitan 10.11.6 Attempt

    Today I attempted to clean install El Capitan 10.11.6 on a vanilla H61N-USB3 following Saganic0's Gigabyte H61N-USB3 - El Capitan SUCCESS!! thread. Unfortunately I can't get the install to boot without the help of the USB installer. I made my USB stick using UniBeast 6.2 from the Install OS X...
  3. sekmo

    Clover boot resolution - Why on the usb installer it is ok?

    Hi! I'm trying to fix this little issue at boot: when I am at the clover screen, I got low resolution, but if I try to boot from my unibeast usb pen, I can get a full 1920x1080 resolution! I'm on a 10.11.3 with clover v2.3k on a h61n-usb3 + i7 3770k (hd 4000) Thanks :-)
  4. Saganic0

    Gigabyte H61N-USB3 - El Capitan SUCCESS!!

    [SUCCESS] Gigabyte H61N-USB3 - El Capitan Hey guys finally got my H61N fully working with El Capitan Spec: - GIGABYTE GA-H61N-USB3 - i5 3570K 3.4GHz - 16GB CORSAIR VENGEANCE BLUE (2x8) - ASUS/NVIDIA GTX 650 1GB - 128GB KINGSTON HYPERX SSD NOTE: DISABLE USB 3.0 FOR THE TIME BEING - This...
  5. skecher

    [Success] Mavericks 10.9.1 GA-H61N-USB3 / I7-3770 / HD4000

    Install 10.9 and apply multibeast after upgrade to 10.9.1 you just need to install graphic driver with multi beast again. The IGPlatformID is crucial for system to boot up without -x as it helps hd4000 driver loaded properly. Credit to this link...
  6. 56reSpuw

    [SUCCESS] Mavericks H61N-USB3 Intel Core i5 HD3000

    [SUCCESS] Mavericks GA-H67N-USB3 Intel Core i5 HD3000 Ive successfully installed Mavericks with the following settings for multibeast 6.0.0: MultiBeast Configuration - 2013-10-23 03:01:30 ----------------------------------------------------------------- Quick Start > UserDSDT -...
  7. jrzjorge

    H61N USB3 IvyBridge

    Using H61N USB3 MOBO f8 bios i3 IvyBridge 3225 CPU no video card using onboard hd4000 500 gig hd 4 gig ram dvi cable I can not get the darn thing to boot at all Using unibeast to boot Reach the usb boot prompt, when pusing enter it goes to black screen flashes the apple sign and...
  8. markassabur

    H61N-USB3 boots to prohibitory symbol after 10.8 install

    Processor 3.19 GHz Intel Core i5 Memory 8 GB 1600 MHz DDR3 Graphics Intel HD Graphics 2000 64 MB of Shared System Memory Software OS X 10.8.2 (12C54) So I have the Graphics card that needs the Special Instructions for AMD 6xxx Graphics Cards: There is an issue with AMD 6xxx cards...
  9. jricica2

    Gigabyte H61N-USB3 - Kernel Panic at various stages of Snow Leopard installation

    Hello all, I have been a long-time subscriber and reader, but this is my first time posting. You all are a great tool, full of resources and knowledge on the complex art of building a Hackintosh! I used the following guide from Lifehacker to build my first Hackintosh because I wanted to...
  10. Dnk_Productions

    1st hackintosh...sooo close, but so far

    All of my components are compatible. Others have had successful builds with mostly OOB success. Here is where I stand: 1. Installed Lion using unibeast. The only way to get unibeast installer to launch was by using: -"GraphicsEnabler=No" -VGA cable -USB stick in...