Search results

I have black screen with NootRX.kext. I do not think that it supports 6900xt, because this card has native macos support.

i removed WhateverGreen.ket and tried to encode HEVC — FCPX encodes 30% of the file quickly (Istat menu shows up to 1,3 MHZ on GPU) and then whole system freezes.

Do you mean HEVC encoding is not possible to be fixed? Why do think that anything besides GPU can be involved?

I also had a weird story with my 6900XT Sapphire TOXIC water cooled (bios was 0x73bf out of the box). Card works well without any spoofing, but it freezes the whole system (Ventura and Sonoma) if you try to encode mp4 h264 in FCPX or Compressor without boot argument -radcodec Now i have...

Sonoma freezes when I try to export mp4 from FCPX or Compressor. Adobe apps work well. SMBIOS MacPro 7,1, GPU — 6900XT. Anyone run in anything similar?

After upgrading to Ventura 13.4 from Monterey 13.4, I start getting strange kernel panic, when Hack is idle for long. It happens from time to time — hack is idle (screen is locked, and turned off), and it wont turn on until hard reboot. Monterey was rock solid. In system log there are a lot of...

Gigabyte Z490 Vision G, not D — Trying fresh Ventura install using this EFI (OC 0.9.2) https://www.tonymacx86.com/threads/gigabyte-z490-vision-d-thunderbolt-3-i5-10400-amd-rx-580.298642/page-1048#post-2368807 After installation, when booting into OS for the first time following errors occurred...

Is on-board Intel Bluetooth and Wifi available? I would like to switch to it from Fenvi to release PCI-e port.

Ventura 13.3.1 — problems with Asus bt400 Bluetooth dongle. It worked fine on Monterey with no extra kext. On Ventura it works with BlueToolFixup.kext, but from time to time Bluetooth stops working, and I have to unplug and plug dongle again. Any ideas?

Which BIOS version is necessary for upgrading to Ventura?

5200 can be, but not 6000

Had no luck with 4800-5600 rates, only turning off XMP and DDR5 auto boost worked (mb hangs with dram red post light for 3-4 minutes, then reboots in BIOS with default RAM settings (4500 MHz)

Aero G DDR5 users — keep in mind, that the Z690 can not handle 4 sticks of high speed RAM with XMP for now. Only two are allowed. Example — ADATA 6000 MHz Lancer XPG DDR5, two 16GB sticks work well with XMP 1 at 6000 MHz, 4 stick 16GB won't POST with XMP1 at all. Without XMP they work at 4500 MHz.

Does it mean we don't need additional kext for second Ethernet port at all?

I have problem on 12.3.1.

I installed latest hackindrom EFI and OC 8.0. Installed new i211 Ethernet Driver for Monterey and it is shown in network interfaces. But when i tried to use top Ethernet port (plugging cable in it), system crashes and reboots.

It is really strange, but I discovered that the video output goes back to normal, if I turned integrated graphic ON. I keep Initial Display Output ad PCIe 1st, and use SMBIOS iMac Pro1,1 (iGPU is not listed, even if it is turned on). Display is attached to dGPU output. How can it be?

No, top resolution is 1080p, if i use DP. I flashed F6, disabled iGFX, chose PCIe 1 output. Disabled Serial port and CMS. With DP i boot into Open Core, picker has low resolution and distort. After picker it boots in black screen. Anydesk shows OS working fine, with right display resolution...

ViewSonic 2758 2k and ViewSonic 2785 4k. The problem with unstable video output occurs both of them. (at the same time, z390 designare with Radeon VII use these displays perfectly). From the first boot after macos install. I have fresh OS. I have fresh new installation, OC 0.7.2, EFI for...

Vision G (BIOS f20), Gigabyte RX 580, Last EFI for Vison G from Hackindrom, SMBIOS iMacPro 1,1. Problems with video output through DisplayPort. It shows only 1080p on my 2K monitor. Through HDMI resolution is correct. Along this, GPU is fully supported (videoproc, FCPX, LUXmark are OK). I tried...