IOPCIFamily FIND 483D0000 0040 REPLACE 483D0000 0080
AND LEAVE MATCH OS EMPTY
this might help also …..
when in clover boot screen press F11 - to clear nvram
and if you are using EHC renaming patches try disabling these
had started to write last post earlier but only got back to it now.
add '-v' and 'debug=0x100' to your boot flags if you start crashing at boot - it will keep the panic code on screen so you can review
did you try with just …._xcpm_core_scope_msrs
that should allow you boot - at least so...
no harm to try them before upgrading - you can always disable them if they don't help
make sure you clone your working drive before updating - don't do what I did and end up with nothing booting.
not sure what changed from version to version but I had more than 2 patches for 10.14.0.
made a bit...
last few trys were with Catalina - mainly as I could only get 10.14.6
i'll stick with dp for time being as it doesn't look to have hindered you
have you done any more with kernel / kext to patch apart from what was already set from the original 10.12 in clover you used?
I know I used patches...
yes , that seems to be the most common issue with 5810 and going back in versions also.
i'll have a another try this weekend .... getting stuck at ' +++++++++++++++++++ ' and then reboots / which is an improvement on couldn't allocate …… if only slightly .once I have a route to reach installer...
not too familiar with hackintool , I used rehabman's method for custom ssdt previously .
hackintool approach looks a simplified version - nothing wrong with that if it suits.
would think kernel patches required for correct power management and usually requires usb to be right also.
If still omitting WhateverGreen , add it in 1.3.4
look at your usb - could be part of the problem …..
try this added to kexts to patch - you should have usbinjectall.kext already
That's what I would use - I installed using that previously from scratch on 10.14.0 with clover 4700 although with
You should have a better shot at correct power management and underlying items with that.
Just my opinion so others here may feel differently.5,1 worked also i...
Still not working for me …..
I know previously - I didn't use 14,2 smbios but works for you so should be enough to reach the installer at least.
had a look thru your drivers and kexts - you have two memory fixes in there ,typically you shouldn't use both together but again if it works it works...
Great stuff , have been doing trial and error with every combination of aptio memory fix and best I can get is
reboot loop @ +++++++++++++++++++++++++++++++++++
free2000 does nothing for me but I know I used it previously ?
get boot loop with osxaptiofixdrv and aptiofix or combinations with...
I popped out the cmos battery last night , reset bios .
Still not reaching installer - must be 10.14.6 causing the issue.
hopefully you get a chance to test Catalina installer - I made usb installer with 10.15.1
Going to try again later today .... if I can reach installer I'll upload what...
downloading 10.14.4 at the moment..... don't understand it either .
i know i didn't use imac smbios last time but i'll stick with what worked for you
did you install to hdd or ssd - do anything with formatting before booting usb installer ?
use any maxmem flags ?which sata port are you booting ...
I've not managed to boot installer either.... Mojave or Catalina
Dell Bios A32
Load Defaults - uefi boot , allow legacy , sata to achi , serial port disabled , vt-d disabled , mem map i/o over 4gb disabled .
Lots of COULDN'T ALLOCATE RUN TIME ...... /
Had mojave working previously on A25...
Mojave version is 10.14.6 so i'll have to try for 10.4.4
next time I have access to a mac.
Bios is set as you have it , will try disabling mem map i/o - have seen others with this enabled / disabled so not a big deal to try with both anyway.
Since my mac access is limited i'll make a Catalina...
Not at home just now , but clover version 4961 ( not nvram emulated ) straight from downloads here.
Not sure of the Mojave version - 10.14.4. or maybe 10.14.6 ,was whatever came via the app store link yesterday
I'll take some screen caps of bios settings later - I did uncheck vt-d etc , serial...