I have MB and CPU as you. Im using Opencore 0.5.8. Trying to get it to work without using Jettison which does work. Memory set to XMP profile 1 in bios. All else works flawlessly. The last piece of the puzzle to solve since its been. bugging me for about a year now. Anythoughts or recommendations
Thanks again esafeddie! Its finally working. I discovered a typo in config. One letter off (fat finger) and once I corrected it all good. Also looking at yours allowed me to tweak mine so its now a little faster on boot
I recently added Opencore Gui and Bootchime to my Catalina 10.15.4 build using OpenCore 0.5.8 on
Board: Gigabyte Z170X-UD5 TH
i7 6700 K
Sapphire RX580 8GB
Original Apple Extreme on PCi adaptor
Samsung 970 500GB
After updating settings I reboot and clear NVRAM via the selection in the GUI
You can test for native NVRAM using this
NVRAM Testing: You can test if your NVRAM is working by running the following Terminal command and rebooting: sudo nvram TestVar=HelloWorld; once you reboot, run sudo nvram -p | grep 'TestVar'; if you see a result, your NVRAM is working; if not, your...
It is possible with Clover. There are instructions on how to upgrade the firmware on Gigabyte GA-Z170X-UD5 TH specifically. That has to be done through windows. Follow the info on this post to upgrade the firmware
tonymacx86's Skylake Thunderbolt 3 Test Build: GA-Z170X-UD5-TH ...
It should work...
You didn't specify which MB or OS you have and I am running Opencore not Clover. Also please remove any system serials or other specifics info from your plist before posting. If its the hot plug issue I discovered it is unresolvable for my motherboard due to the fact that it not on the XHC...
hanks for the suggestion. Unfortunately it doesn't work. On this board the thunderbolt/USBC are on the pcie bus and are not hot swappable on a real Mac so there is no way to make that happen. It does work if its plugged in at boot but will not reconnect if unplugged
I Started this project due to the fact that I could not resolve a sleep wake issue that started since I upgraded to Catalina 10.15.4. I previously went through all the guides and created an SSDT for Clover for my USB ports which appeared to have initially caused the problem back in Mojave. That...
I would suggest that you go back to Hackintool and recreate your USB map but use the SSDT it creates along with the SSDT-EC-USBX instead of the USB kext. AlsoSSDT-Plug and SSDT-PMC are missing the extension.aml. SSDT-EC-USBX need to be added to the ACPI folder and added to config.plist
Went back and completely rebuilt my SSDT for USB. All works fine sleep now works ( it seemed mounted USB hard drives cause sleep to fail)
With open core I can't see my USB C ports at all where they worked fine in clover. Any thoughts?
UPDATE: followed the Vanilla Guide explicitly when setting...
I entered my SSDT correctly into config.plist. My kext order is:
All other settings are correct as everything works perfectly. iMessage, bluetooth wifi handoff airdrop full graphics accelaeration
I can't seem to figure out what I'm missing.
In an attempt to fix sleep/wake issues I decided to experiment with open core. following the guide( read it through before starting) I was able to create and install OS 10.15.4 on an external SSD using OC.5.6. I had previously created an SSDT for USB so I used that with success. I then restored...
will not wake from sleep after upgrading to 10.15.3. Never had an issue before this on any other version
this is the result of my failure records
2020-02-07 10:57:52 -0500 Failure Failure during wake...
I can’t get my custom ringtones to work on Catalina. They’re in my iTunes folder, they work on my phone but I cannot select them via my contacts. Do I need to move them to a different location?If so where?