Search results

I think I've bricked my computer in the stupidest way possible. I was waiting on the High Sierra install to finish it's thing and reboot while laying in bed. Since the estimate was at 12 hours, I turned the brightness all the way down which turns off the screen completely on my laptop. While I...

The outer shell will probably be pretty hard, but you should be able to repair the front grill just around the disk drive with a rubber mallet. If you can't find a rubber mallet, tie a thick cloth over a hammer and hit lightly. A heat gun might help soften the metal up a bit too. If you don't...

If you plan to Hackintosh, you need to pick the PC components specifically for that. Just follow this guide: https://www.tonymacx86.com/buyersguide/july/2017 Not to be mean or anything, but I don't think anyone wants to design a build for you, and give you step by step instruction when with...

It's been a bit since I posted an update, but I've been slowly painting everything. Here's a sample of the G5 plate in red and black. It still needs a bit of touch up, but so far it looks pretty cool.

Combine The two ground pins from each -> -1 pin Combine the +12v pins -> -1 pin 8 - 1 - 1 = 6 pins needed. Combine the two red pins and the two black pins to be one pin.

There should be 12 nuts at the two joints which hold down a metal plate. You can see the threads for the nuts in the left part of the picture below.

Yes, every single screw needs to come out to remove it without causing damage. There are also some nuts on the back side of the side of the case. If you run your hand over the inside of the lip right where the side panel goes on you will feel them. I would recommend getting a larger handled...

I got the power supply mount completed yesterday, I'm happy with the shape, but I think it needs to be reinforced a bit.

I got my fan shroud printed and I'm really happy with it! There are a few holes that I'll need to fill and sand, the surface is a bit rough, and it revealed a gap in the G5 shield that shows me the mounts I made to replace the PSU are not quite straight. All of these are fixable and I think it's...

I got my fan grills printed out, and I'm really happy with the way they turned out. Next up, I'm going to print a piece that will sit between the G5 CPU shroud and the fans like the original case had.

I took me awhile, but I finally got my logo mod finished for my GPU. The last picture really doesn't do it justice, I had to turn the light out and unfocus the camera to get it to hold an color. It's a very mild red glow, it definitely doesn't "shine" like it used to, which I'm actually happy...

I would personally run a fan directly on the cpu heatsink, though you could also just try it and see what happens without it. CPUs have pretty great thermal cutoffs, so just run some synthetic loads (any CPU benchmark should be fine) and see if the system runs hotter than you want or completely...

I got the back plate epoxied in, and it looks decent. The plastic is a little flimsy, but when I screw the fans in, it adds a lot of rigidity, so I'm not too worried about it. I also have to print out some fan guards for the holes.

Check out this thread: https://www.tonymacx86.com/threads/g5-front-panel-quick-guide.77208/

The larger parts cost maybe 75c, but it depends on what filament you use. I prototype my parts in cheap Chinese filament that I got for $18/Kg, nicer stuff can cost $20-30/Kg, but it prints more reliably. The prusa is probably the best you can get if you want a top of the line entry level...

Prusa i3 Mk2: http://shop.prusa3d.com/en/3d-printers/59-original-prusa-i3-mk2-kit.html

I got a prototype back panel printed and test fitted. I need to narrow the width of the back panel by about 2mm, but otherwise, the piece fits very well. I also mounted up the fans just as a test for the size of the screw holes. Currently it is printed with hexagons instead of solid fill so it...

Yup, happened to me when I originally drilled the back out, and I had to redo it, thanks for the tip. I cut the back of the case out rough. It needs to be filed down at the edges and I need to print the new back plate that will be going there. I clamped the piece I cut out of the back and I'm...

I ended up changing gears completely with the front panel since I just couldn't get the shape of the metal correct and I realized that the audio jack will never work with the hardware I have.. I found a usb 3.1 and usb type c panel online. I 3D printed out an adapter since the mounting screws on...

I got a prototype printed for the front panel. The back of it is simply flat right now, but I'll be adding in mounting points for the audio jack and two usb ports next.