Recent content by vantamac

  1. vantamac

    Mojave on Z490 Vision G (10850k)+ RX580 Clover or Opencore?

    Thanks for the tip I will look into that post.! I did use Opencore for the catalina install usb. I used that same EFI folder on my Mojave SSD, but it wont start.
  2. vantamac

    Mojave on Z490 Vision G (10850k)+ RX580 Clover or Opencore?

    So I created an install USB with Catalina to see if It was able to boot and install and check everything was fine. (For now I only used internal GPU, waiting for the RX 580 to arrive) Everything went smooth I used EFI I found on a Github page from Schmocklord. I just added generated serial...
  3. vantamac

    Mojave on Z490 Vision G (10850k)+ RX580 Clover or Opencore?

    Hi all, Im trying to build this new mobo with Mojave because I need some 32bit apps that wont work on Catalina or Big Sur. The question is, is it even possible to install Mojave on this new architecture? If so, which route should I go? Clover or Opencore ? Or could I reuse my working Mojave...
  4. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Well , I just put it into my other PC ( Ga Z77 DS3H) El Capitan / High Sierra ( I have 2 systems on that PC) and it is working, recognized and ports available, My Focusrite Pro 40 is connected and everything, so it is compatible. I just swaped the working Firewire PCI ( adifferent card vendor)...
  5. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Here: https://www.startech.com/Cards-Adapters/FireWire/4-Port-IEEE-1394-FireWire-PCI-Card~PCI1394MP
  6. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Ok, I got a tiny bit further : I used Cover Configurator clicked under fixes ACPI /FixFIREWIRE Firewire card finally recognized under PCI in System Report but under section Firewire it says "No Firewireports were found" This is the System Report output under PCI: pci104c,8024: Type...
  7. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Thanks again for your help: Just a quick one: Im surprised because the system runs quite "smoothly" i think apart from the Firewire card issue not being recognized Did I forget some of the steps of your guide? How do I fix this? ( or do I need to fix this , what is the downside of having the...
  8. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    I used 2 different programs IOjones and Ioregexplorarer, attached both saved results. Thanks for helping me out!
  9. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Quick note. I tried installing some PCIe cards on the other slots and also not recognized. So the only one recognized is where the Graphic card sits, all the others pci slots are nonexistent to the OS
  10. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Hey guys thanks a lot for your help and support. But this DSDT stuff is a bit above my knowledge. I read and tried to replicate some of the stuff I have seenhere in the forum, but im unable to compile the DSDT.aml I managed surprisingly to "fix" almost 4 errors using google searches and here in...
  11. vantamac

    [Guide] HP 6300 Pro / HP 8300 Elite - A 100 percent Working and Easily Affordable CustoMac

    Hi everyone, Finished installing High Sierra using this impressive and easy to follow Guide on my HP6300 i5-3470 6GB RAM GT720 (BIOS V2.99) Everything is working so far, except my Firewire Card PCI.... LINK: Startech FireWire Card 1394 PCI I tried to install a Firewire PCI Card into the only...
Back
Top