Recent content by SnapMan

Take a look at http://www.dremeljunkie.com/2011/11/all-in-one-20-imac-g4-genuine-tmds-to.html He uses the internal monitor to connect to a NUC board.

Picked up an 13" MBP 2.5 GHZ IB 500 GB HDD 4 GB RAM. (Fry's special $999) Liking it very much, pretty fast, great battery life, updated to Mountain Lion.....had to reinstall a couple of times for it to work. Haven't used any of the ports aside from USB and headphones, but going to pick up a...

I think that iBoot is only for Snow Leopard. Even when using iBoot to install SL, you only put the DSDT on the desktop and MultiBeast installs it. Perhaps you can give us a few more details about what install method you are using, so we can help you. The more details the better.

How did you install? DSDT? 10.7.x? What drivers/kexts did you install? The more info, the easier to sort out. One good way to isolate the problem is to start up and stop at the Chimera screen, then type -v for verbose mode, then watch the startup sequence, when it freezes, you might get some...

Glad it is not a hardware issue! The reason probably has to do with power management that is specific to the Ivy Bridge or the MB, I believe there is a bridge helper app on the downloads page that might help: If you are not running 10.7.4 and that doesn't solve it, give us more specifics on...

Re: Stuck on Apple logo after Unibeast lion clean install I don't think the TM B/U will work as it doesn't have the necessary boot loader and kexts required to run on non-Apple hardware. iBoot doesn't work with Lion, do you mean rBoot? Did you try adding boot flags? GraphicsEnabler=NO might help.

It is possible a hardware issue. What I would do is unplug the HDDs and try to boot into BIOS again. If you can, set BIOS again as per your original installation. If you can't get into BIOS, try reseating the RAM and the processor. Make sure all your connectors are fully seated and try again...

Yes, there are posts on every build, I believe most people manage to get it working without posting. If it is a recommended build, it has been successfully installed a number of times. Please tell us what you have done. Have you for instance tried adding GraphicsEnabler=NO or -X at the...

8 months old? It should be under warranty and Apple should fix it for free. I would take it back ASAP!

You are correct, should work with YES, I suggest using the Search function above, there are several discussions on what might have gone amiss including: http://www.tonymacx86.com/viewtopic.php?f=169&t=39114

Re: Boot problem 10.7.4 after a bad move (broken bootloader?) You might consider burning an rBoot disk and booting with that in the DVD drive, that will allow you access to your HDD and you can run MultiBeast again if need be. Have you tried booting with -x PCIRootUID=1 and/or GraphicsEnabler=NO

The DSDT is installed in the Extra folder and after you run MB, you can delete it. Realtek ALC889 codec on that board. If you installed Voodoo and wish to remove it, it is installed in the System/Library/Extensions folder. Just remove it, install the Realtek kext and run system utilities in MB...

You can set GE=NO in MultiBeast so that it boots that way every time. IIRC you use GE=NO for Intel graphics.

That is a good question! All the 6870 cards listed in the Wiki have the same device ID, so it looks as if they are either identical or close to it. Note that the details on getting them working are slightly different, so you have a few options should it not work immediately...

My experience is you only need to re-install AppleHDARollback when updating. We used to keep more stuff in the Extra folder, but it was folded back into the main extensions folder for some reason. Keep in mind that when Rollback is installed, it replaces the AppleHDA file using the same name, so...