have you still the same issue ? I have the same board and same issue currently with Clover v5100 and I think I found the issue.
When I boot from HDD or SSD, I also have low res 1024x768. If you check About, at the bottom of the page I guess you have :
EFI Revision 2.10,
Platform : x86_64...
But I have the same issue with my two CPUs : Gigabyte H61N-USB3 Bios F8/Pentium G2020 IveBidge (log below) or a Gigabyte GA-H67MA-UD2H-B3 Bios F8/Core i3-2105 SandyBridge
Moreover there is the -p command line option that allow to force the type of CPU, no ?
I have compile errors with a Gigabyte H61N-USB3 Bios F8/Pentium G2020 IveBidge (log below) or a Gigabyte GA-H67MA-UD2H-B3 Bios F8/Core i3-2105 SandyBridge
Log below is with the G2020 and -d 2 option, ACPI folder content attached.
What's wrong ?
ssdtPRGen.sh v0.9 Copyright (c)...
Try to run the script but it says I forgot to press F4 :
You forgot to press F4 or Fn+F4 at clover boot screen.
Please reboot and press F4 or Fn+F4 to dump ACPI origin files.
But I have pressed F4 and I have the following files in origin folder :
what's wrong ?
EDIT : I checked...
On point 2, I end up reinstalling Mojave and use a minimal config.plist and Mojave is now booting properly with my GT710. Apparently, my initial installation was corrupted.
On point 1, Mojave and GT710 give also overscan with my TV Sony KDL-32V2500 (via HMDI or DVI/HDMI) and I...
I'm just updating my old hack (legacy boot with Gigabyte H67MA-UD2H-B3, SandyBridge i3-2105 with a GT710) to Mojave (already booting with Clover 4920, lilu, AppleALC and WEG) and soon to Catalina (with clover 5100) and was wondering which guide I should use for proper Power Management and...
I am facing 2 issues and was wondering if Hackintool could help on this:
1. Overscan when connecting to my TV
2. Black screen with a GT710 and Mojave
My config : Gigabyte H67MA-UD2H-B3 with a i3-2105 (Sandy Bridge) with HD3000 and a GT710 for Mojave, clover 4920 in legacy mode, SMBIOS...
I am updating my old hack (from Mavericks) to HighSierra 10.13.6 (17G65) and Mojave 10.14.6 (18G95) with an MSI GT710 1Gb and this works fine with HS but I got a black screen with Mojave.
My MB is a Gigabyte H67MA-UD2H-B3 with a i3-2105 (Sandy Bridge) with HD3000 and a single hard disk with...
I am updating my old HTPC with HD3000 to HS and Mojave and need to configure again Audio on HDMI.
Post #1 says it's for HD4000 and newer : knowing I will use clover and recent OSX release, should I follow this guide while I have an HD3000 or the previous guide ?
I'm curretly updating to Mojave my old HTPC with a Sandybridge HD3000 which is not supported anymore by Mojave.
I am therefore looking for a fanless low end graphic card. Fanless GT710 would be a good choice, quite cheap but apparently only until 2021.
What would be the AMD equivalent ?
Now that Catalina is out, I started to update my old Gigabyte H67MA-UD2H-B3 with Core i3-2105 running El Capitan to Mojave. As at that time I did not knew Mojave does not support HD3000, I started to install with an USB Stick made with Unibeast 9.2 and Mojave 10.14.6 (18G95)...