Recent content by ono

I feel very honored to receive your message. What you have written is rigorously true. Meanwhile I bought an AMD video card Radeon RX 560 and this responds to all the requirements for macOS Ventura. On a computer with Kaby Lake processor ( like my Desktop ), it is not recommended to install...

On Finder, goto /Library/Logs/DiagnosticReports delete file shutdown_stall* delete file wake* or delete all file here for that matter. Thanks, maxxx! Your indication also solved my problem.

Solved! My Catalina MacOS and my Monterey MacOS work well both with SMBIOS for iMac19,2 but without any PCI-e video card. Just intel Graphic 630.

I studied the DeviceProperties settings model you sent me, in detail. They are the same for me, except for the PciRoot(0x0)/Pci(0x1b,0x0) address which I deleted and replaced with the address indicated by hdef obtained with IORegistry Explorer. But about the SMBIOS settings: you chose the...

I made all the changes indicated, but I found that the display is strongly dependent on the SMBIOS parameters specified in OC/PlatformInfo/Generic. So far, I've managed to find those SMBIOS values that only work with processor graphics (HD graphic 630, corresponding to Kaby Lake i-3 7100...

Kaby Lake: Gigabyte H110 with i3-7100 processor and NVIDIA GeForce 730 PCI-e card. The Gigabyte H110 motherboard offers the possibility to select from the BIOS, either iGPU or PCIe graphic card. Monterey is known not to support NVIDIA video cards. That's why I wanted to remove the NVIDIA video...

Post Install workaround also includes installing a wifi interface. I had a BCM 94360 CS card bought for my laptop, on which I had Mojave installed. Now the laptop has another operating system. I mounted this board on a PCIe wifi support and put it in the computer with Monterey. The surprise is...

Yesterday I bought a PCIe Radeon RX 470/570 8 GB graphics card and all these problems have been solved. Boot time of about 30 sec, sleep / wake works normally. Now I have a fully functional computer and thank you from the bottom of my heart for the generosity and kindness with which you helped me!

My port is a Tipy-C+Sw one. Thank you, now I have the right UBBPorts.kext. The port remains the same. Your opinion, please?

BIOS->Advanced->Onboard Devices Configuration->Serial Port == OFF. Aye-Aye, Sir! I understood now! And I do again my USBPorts kext and my new SSDT-EC-USBX. Then insert the Type-C device again My USB stick has 1 end == USB3-Type C, but another end is a USB3-Type A end. So I need a special...

No, these are all the ports I counted. Yes, there are 6 ports on the back panel. And on the handmade sketch, I wrote what I read on Hackintool for the stick inserted in that port. For example, in the back port, top left: when I inserted the USB-2 stick, hackintool showed me PRT4. Then, after...

I worked on the OpenCore installation guide. Now I'm about to fix USM mapping, but I have some ambiguities, although I received valuable guidance in a previous case. I only had one USB controller there, but here, I think there are two USB controllers. ( IOREG_XHC.png). To detect the USB ports I...

I installed macOS Monterey 12.2.1 on this computer. Now I am going to solve the post-installation steps. The first step was to set the audio. First I installed Ubuntu ( on a second hard drive ) in order to get the necessary hardware data. The computer was bought by second hand, so I didn't know...

SUCCESS! First of all, I would like to thank EdHawk from the bottom of my heart for his help, as well as the other colleagues - Gigamaxx - who gave me such valuable guidance. I carefully studied the EFI folder posted by EdHawk so I could understand where I was wrong. The config.plist in the...

Sorry, Big Sur macOS installer.