Recent content by ninjamoby

  1. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    Delayed update. I think the ethernet port on my motherboard is just shorted / fried. Can anyone recommend a PCI ethernet card that works with this motherboard?
  2. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    Still working on this but haven't gotten a solution yet to inject network kexts and get ethernet back.
  3. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    It's definitely loading the kexts from the Clover EFI directory (because that's the only one Clover is installed on, I checked the others). I dual boot to Windows on a different drive but double check BIOS isn't loading that drive first. I ran "kextstat" in terminal, and it seems like Clover...
  4. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    Ethernet enabled in Bios and I attached the zip file below. Much appreciation for your guidance.
  5. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    Thanks. I switched over to OTHER. All the other kexts still work. Ethernet issue remains the same as before.
  6. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    Thanks Pilgrim. I'm wary to change this as it was a pain in the butt to get audio and other things back in the day. Should it be seamless moving from 10.12 to Other folder?
  7. ninjamoby

    Sierra z68x-ud3h-b3 No Ethernet Detected (10.12.6)

    Having the problem with ethernet not registering as en0 in order to access App Store. It used to work, but somewhere along the line WiFi became en0 so things needed to be fixed. I've followed the instructions to remove the network devices SysPrefs->Network, delete networkinterfaces.plist...
  8. ninjamoby

    Direct Update to macOS Sierra using Clover

    I'm getting the following error after the macOS installer runs for about 20 minutes. "macOS could not be installed on your computer Building boot caches on boot helper partition failed. Quit the installer to restart your computer and try again." Any recommendations for how to proceed?
  9. ninjamoby

    Could not find IOPlatformPlugin Driver (10.10.5)

    Hi all- After a stable Yosemite install on Clover, my USB 3.0 stopped working a few days ago. I installed via kext wizard a recommended USB3 kext from Rehabman. Restarted. Everything worked fine, including the USB 3 drives. However after locking up earlier today, I get the following messages...
  10. ninjamoby

    OS X 10.10.5 Update

    The update failed for me, and I had to do a clean install. However, I have no audio (on a Clover boot). Running Multibeast (which usually fixes the problem) instead gives me an: "Installation Failed" error. The multibeast log says the following with regards to the error: installer...
  11. ninjamoby

    Caught in Loop After 10.10.3 Update

    I've tried booting with these flags. Normally with a graphics issue, the computer will reset or freeze during the boot. In this case, it loops these screens with the "Sandbox" deny information repeatedly infinitely.
  12. ninjamoby

    Caught in Loop After 10.10.3 Update

    Hoping this doesn't require a complete reinstall.
  13. ninjamoby

    Caught in Loop After 10.10.3 Update

    As per the attached screengrabs of the verbose logs, my computer is now stuck in a loop when booting up. Any advice on how to proceed?
Back
Top