Recent content by jordya

Hi b166ar, I just installed a Fenvi FV-T919 BCM94360 BT/Wifi card and everything seems to be working. However, my Mesasges app is sending all messages as SMS (green), not iMessage (blue). I've tested by just sending to an iPhone and same result. Did you experience this or do you have any...

Thanks for the suggestion...I think I found the problem. The firewire interface appears to be the issue...I tried using just the onboard sound and fcpx functions as normal. I had not been using the onboard sound due to static and squealing sounds I get from the onboard sound to my speakers (I...

Will do. Thanks again for taking the time. :) EDIT: attached is my EssentialsList.zip

here are my kexts in L/E/

Thank you for that explination. I can confirm my igpu is active and running as expected. If you think of anything that might be causing my audio issue in fcpx, it would be greatly appreciated. My setup is similar to yours, but I have also tried using your exact setup from your latest github...

Ok then...guess I’m back to the drawing board with troubleshooting. You mentioned in a previous post to use the intel power tool to verify if the igpu is being used. I did this but honestly, I could not totally understand what I was seeing. In the first box, the core was being hit while the...

@b166ar thank you for this guide. It has been very helpful. Can you confirm if you are able to hear audio from movie clips you are about to import into fcpx? I have footage recorded with my iPhone and when I open the import screen or when I scrub already imported footage (before dragging to...

yeah, was planning on that this weekend when I update...just thought I'd see if anyone knew how that affected the 7700k proc. I'll post an update when I can. thanks.

Do you know if removing Inject Intel and the ig-platform-id would work on a Gigabyte Z270XP-SLI with an i7-7700k? I seem to recall reading that will only work on the Coffee Lake procs...any thoughts?

Hi all...thanks for creating this forum...it's been extremely helpful. After following this forum and setting up the same, I am running into issues regarding FCPx export times (specifically the BruceX benchmark). I'm using a Gigabyte Nvidia 1050ti GPU and it's setup to use hardware acceleration...

I installed.104 and noticed a slight improvement (maybe 10 seconds) but still around the 2 min mark for completing. I did see that if I changed the ig-platform-id from 0x59120003 to 0x59120000, I do see both the Intel HD and Nvidia listed in system report...but then FCPX crashes the whole...

The demo at madebyevan.com runs very smooth...no issues that I can see. I am running 10.13.3 As for 104, I can try that. Given the issues with Nvidia drivers and 10.13.3, I had to download 103, edit the package, install, and update NVDAStartupWeb.kext to work properly...instructions from...

I also have a similar setup and I'm seeing terrible FCPX performance when benchmarking BruceX...around 2 mins. I was able to get "Hardware Encoding Supported = Yes" working, but no improvement at all when running BruceX. My setup: i7 7700K, GTX 1050ti, Gigabyte Z270XP-SLI, 32GB RAM running...

I'm using the 1050ti with i7 7700k processor. I'm getting almost 2 minutes to complete BruceX 5k. I am using Nvidia driver 378.10.10.1025.103. do you have any ideas on how I can improve my performance? I would love to get the 31 seconds you are getting. Maybe you can post your config.plist and...

10.13.3 - FCP: 10.4 i7 7700K 32GB DDR4 RAM Gigabyte Z270XP-SLI Gigabyte 1050 TI 4GB Samsung 960 EVO NVMe 500GB I'm seeing around 2 minutes...can't seem to resolve this. Any advice?